Facet GOLD-FLO Electrical Fuel Pumps
Facet GOLD-FLO Electrical Fuel Pumps

Facet GOLD-FLO Electrical Fuel Pumps

Facet GOLD-FLO Electrical Fuel Pumps.

Fuel Compatibility: All models of the Facet® High Performance GOLD-FLO® Solid State Fuel Pumps are compatible with gasoline, diesel, biodiesel, E85, blended alcohol fuels and fuel additives.

  • Reliability:
    The new GOLD-FLO® Solid State Fuel Pump is an enhanced version of the Interrupter model. It has Solid State circuitry and will meet or exceed all performance specifications and is totally interchangeable.
    (These pumps have demonstrated an endurance life almost double that of the nearest competitor, according to our test data).
  • Easy to Install-Easy to Service:
    Two bolt mounting makes installations easy.
    Nothing to adjust.
    For best results, mount the pump close to the fuel tank and below the fuel level.
    The pump is self-priming to 24 inches vertical fuel lift.
    Vertical mounting is preferred to assure maintenance of rated pressures.
    The only service normally required is a simple cleaning of the filter and fuel inlet cavity.
  • Eliminates Vapor Lock:
    When properly installed on most vehicles a constant, smooth, dependable supply of fuel under pressure is assured in the hottest weather or in high altitudes.

Features:

  • State of the art Electronics
  • Sealed Electronics
  • Built in Anti-Siphon Valve (Positive shut-off)
  • Standard equipped with replaceable 74 micron filter
  • Optional replaceable 200 micron filter available especially for Diesel engines
  • Built in magnet to collect metal particles for additional filtration
  • 1.6 amp average
  • Self Priming and Self Regulating
  • Weighing only 32 ounces and 5 inches long
  • Corrosion Resistant over 100 hours of salt spray
  • Operating Temperature Range: -40F to 180F

Depending on your vehicle's carburetors and the Facet GOLD-FLO pump of your choice, it might be required to use a pressure regulator.
Please check the GOLD-FLO specifications against the requirements of your vehicle to be sure.

The Facet GOLD-FLO pumps that we carry use a 1/4" NPFT tapered thread for the connectors.
You will find these connectors HERE.

Facet GOLD-FLO Electrical Fuel Pumps

!
RTWK
Facet GOLD-FLO Red top Competition Fuel Pump Kit

Facet GOLD-FLO Red top Competition Fuel Pump Kit

Facet GOLD-FLO Red top competition fuel pump kit suitable for engines of 200+ BHP.

Pump specification:

  • Flow rate 45 Gallons/hour / 170 liters/hour
  • Pressure: 6.5 - 8 PSI / 0.45 - 0.55 Bar
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • Mounting isolation feet
  • 10 mm Inlet and outlet unions
  • Spare internal filter
  • Terminated earthing wire
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread
Fuel Unions for fuel lines with 10 mm internal diameter

Due to its operating pressure of up to 8 PSI (some 0.55 Bar), the GOLD-FLO Red Top Competition pump usually requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet GOLD-FLO Red top Competition Fuel Pump Kit

RTW
Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

Facet Red Top competition fuel pump, suitable for engines of 200+ BHP.

Pump specification:

  • Flow rate 45 Gallons/hour / 170 liters/hour
  • Pressure: 6.5 - 8 PSI / 0.45 - 0.55 Bar
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread

Due to its operating pressure of up to 8 PSI (some 0.55 Bar), the GOLD-FLO Red Top Competition pump usually requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

FPA908R
74 Micron Replacement Facet GOLD-FLO Fuel Pump Filter Element

74 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

Replacement Facet Fuel Pump Filter Element in 74 Micron.

Fits the Facet GOLD-FLO and Interrupter series fuel pumps.

Suitable for gasoline and alcohol engines.

For Diesel engines and situations where a higher degree of filtration is required, please use the 200 Micron filter.

 

74 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

FPA908B
200 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

200 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

Replacement Facet Fuel Pump Filter Element in 200 Micron.

Fits the Facet GOLD-FLO and Interrupter series fuel pumps.

Especially designed for Diesel engines and situations where the standard filter of 74 Micron doesn't suffice.

 

 

200 Micron Replacement Filter Element for Facet GOLD-FLO Fuel Pumps

FPA905
Facet Fuel Pump Mounting Kit

Facet Fuel Pump Mounting Kit

Facet Fuel Pump Mounting Kit.

Antivibration mounts + earthing wire for Facet Cube, GOLD-FLO and Interrupter series fuel pumps.

Facet Fuel Pump Mounting Kit

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch