Airtex Electrical Fuel Pumps
Airtex Electrical Fuel Pumps

Airtex Electrical Fuel Pumps

Airtex Electrical Fuel Pumps.

On this page you will find our offerings on the electrical fuel pumps by Airtex.

Airtex Electrical Fuel Pumps

!
WFP509
Airtex 6 Volt Low-Pressure Fuel Pump

Airtex 6 Volt Low-Pressure Fuel Pump

This is a special fuel pump for vehicles with a 6 Volt electrical system.

Thanks to its low output pressure of 4.4 PSI / 0.3 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

Pump specification:

  • Flow rate: 8 Gallons/hour - 30 liters/hour
  • Pressure: 4.4 PSI / 0.3 Bar
  • Pipe union thread size: 1/8" NPTF tapered thread
  • Power supply: 6 Volt Negative Earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • In-line fuel filter
  • Mounting bracket and materials
  • 8 mm inlet and outlet unions with fuel hose and hose clips
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Always operate this pump with the proper filter installed as failure to do so will void the warranty!
Replacement filters can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

Airtex 6 Volt Low-Pressure Fuel Pump

WFP502
Airtex 12 Volt Low-Pressure Fuel Pump

Airtex 12 Volt Low-Pressure Fuel Pump

This is a special, low-pressure fuel pump for vehicles with a 12 Volt electrical system.

Thanks to its low pressure of 4.5 PSI / 0.31 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

Pump specification:

  • Flow rate: 90 - 130 liters/hour
  • Pressure: 2.5 - 4.5 PSI / 0.17 - 0.31 Bar
  • Pipe union thread size: 1/8" NPTF tapered thread
  • Power supply: 12 Volt Negative Earth
  • Pump Length: 172 mm
  • Pump Diameter: 54 mm
  • Draws a current of some 5 Amps
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

The kit includes:

  • Pump
  • In-line fuel filter
  • Mounting bracket and materials
  • 8 mm inlet and outlet unions with fuel hose and hose clips
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Always operate this pump with the proper filter installed as failure to do so will void the warranty!
Replacement filters can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Airtex 12 Volt Low-Pressure Fuel Pump

FPA906

1/8'' Screw-On Fuel Pump Filter

This is a special screw-on fuel filter to be used with a variety of electric fuel pumps.

Failure to operate those pumps with a suitable filter like this usually voids the warranty on the pump!

This filter suits, amongst others, the Airtex 6Volt filter and the range of Solid State fuel filters by Facet.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Union for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

1/8'' Screw-On Fuel Pump Filter

LOCTITE2430ML
10 ml Loctite 243 Thread Locker

10 ml Loctite 243 Thread Locker

In order to thoroughly seal the connection of screw-in couplings and to firmly lock them, we advise you to use this Loctite 243 thread locker.

Supplied in a bottle of 10 ml / 11 grams.

Loctite 243 offers a medium locking power which will allow you to easily disassemble screwed connections while still firmly securing those same connections and preventing them from undoing themselves wile in operation.

As an alternative, you can use our Superior Quality PTFE tape which will offer excellent sealing properties.

10 ml Loctite 243 Thread Locker

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch