Service kit for the Solex and Pierburg PICT 28 carburetors as used mainly on the Volkswagen Beetle 1200.

Although these carburetors were originally delivered on the above cars, they are often transplanted onto other cars and engines so the range of vehicles that these service kits might fit is much broader.

Alternatively, your car might no longer be equipped with the carburetor that it left the factory with.

So, please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.

This service kit contains, amongst others, the following parts to service 1 carburettor:

• Base gasket
• Float chamber gaskets
• Copper washer
• Pump diaphragm
• Needle valve - size 1.50

Please note that Solex PICT was also sold as Pierburg PICT and that both these carburettors use the same rebuild kit.

This is a Carburetor City service kit of outstanding Italian manufacture.

Service kit for the Solex and Pierburg PIC and PICT carburetors as used mainly on the following Volkswagen models:

• Volkswagen VW 1303 cc
• Volkswagen VW 1600 cc
• Volkswagen VW Polo S 800 cc
• Volkswagen VW Polo 900
• Volkswagen VW Polo 900 Coupe 1050 cc
• Volkswagen VW Polo S/SL 1100 cc
• Volkswagen VW Derby L 900 cc en 1050 cc
• Volkswagen VW Derby S/LS 1100 cc
• Volkswagen VW Golf 1050 cc
• Volkswagen VW Golf 1100 cc
• Volkswagen VW Golf S/LS/GLS 1460 cc
• Volkswagen VW 1600 cc
• Volkswagen VW Golf S/AT 1500 cc
• Volkswagen VW Jetta 1300 / 1500 / 1600
• Volkswagen VW Scirocco - Rabbit 1460 cc
• Volkswagen VW Scirocco S/AT
• Volkswagen VW Scirocco 1500

It fits the following variations of the Pierburg and Solex PICT and PIC carburetors:

• 34 PICT 3
• 34 PICT 4
• 34 PICT 5
• 31 PIC 5
• 31 PIC 6
• 31 PIC 7

Although these carburetors were originally delivered on the above cars, they are often transplanted onto other cars and engines so the range of vehicles that these service kits might fit is much broader.

Alternatively, your car might no longer be equipped with the carburetor that it left the factory with.

So, please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.

This service kit contains, amongst others, the following parts to service 1 carburettor:

• Various gaskets
• Various copper washers
• Various aluminum washers
• Various rubber (Viton) rings
• Various diaphragms
• Needle valve

Please note that both the Solex PIC and Solex PICT were also sold as Pierburg PIC and Pierburg PICT.

This is a Carburetor City service kit of outstanding Italian manufacture.

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

• 0.15 MM
• 0.25 MM
• 0.4 MM
• 0.8 MM
• 1.6 MM

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose.

This fuel hose has an actual inner diameter of 7.5 mm and 13.5 mm outer diameter and therewith a nice and tight fit for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

• Cover: Black smooth CR
• Reinforcement: High tensile synthetic textile plies
• Liner: Black smooth NBR

Temperature:

• -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

• 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

• Regular working pressure: 10 Bars / 145 PSI
• Tested pressure: 20 Bars / 290 PSI
• Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

• 70 mm

This hose uses 11 - 13 mm jubilee clips.

Endless Band Hose Clamp with Buckle - 5 mm wide.

Again one of those items that allow you to put the finishing touches on a restoration!

This is the famous "endless band hose clamp with buckle" that was used throughout the 1950's, 1960's and 1970's in the car industry.

Unfortunately, these band clamps are only suitable for one-time use and are discarded after removing them.

Over the years, these clamps have become harder and harder to find but we managed to find a source!

We are selling these in sets of 3.

Such a set consist of the following:

• Approximately 100 cm Zinc-plated band, 5 millimeters wide
• 3 buckles

This way, you have roughly a foot (or 33 cm) of band per clamp / buckle which is more than enough for regular applications.

Thanks to the generous length of band, there is virtually no limit to the diameter or circumference of the clamp that you wish to apply although these were usually applied to small diameter fuel lines.

Please note that this style of clamping is NOT suitable for stainless steel-braided lines.

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

This is the top-of-the-line Cohline, steel-braided E10-resistant, flexible fuel line / hose.

This fuel hose has an 8 mm inner diameter and 16 mm outer diameter and is therewith suitable for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

• Cover: Black smooth CR
• Reinforcement: High tensile synthetic textile plies
• Liner: Black smooth NBR

Temperature:

• -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

• 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

• Regular working pressure: 10 Bars / 145 PSI
• Tested pressure: 20 Bars / 290 PSI
• Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

• 70 mm

 This hose uses 14 - 16 mm jubilee clips.

Sytec Fuel Line One Way Valve.

We have two versions available:

• Suitable for 6 mm internal diameter fuel hoses
• Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

• 4 pin vises to suit all drill sizes included
• 10 drills ranging from 1,0 to 2,0 mm:
  1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
• 20 drills ranging is size from 0.3 mm to 1.6 mm:
  0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
• 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

• 1 pin vise to suit all reamer sizes in this set
• 1 storage case
• 16 reamers ranging is size from 0.33 mm to 2.00 mm:
  0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

• See-Through Spark Plug
• Hexagonal adapter for spark plug wrench
• Copper sealing washer
• Extension Cord
• Extension tube with mirror
• Cleaning brush
• Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

• 10 mm
• 12 mm
• 14 mm - SOLD OUT AT THE MOMENT!

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Car Balancer.

Internal combustion engines use a mixture of air and petrol to generate their power.

The performance therefore is influenced by the air flowing into it and the petrol that is metered out by the carburettor.

Unless the air flow in Twin or Multiple carburettors is correctly set, the correct mixture adjustment is unlikely to be achieved and this is the simplest tool to achieve that.

Suitable for use on SU, Solex, Auto-Lite (Fomoco), Stromberg, Weber and Zenith and can be adjusted to fit most carburettors including sidedraft, downdraft with air intakes (Venturi) from 25 mm to 67 mm (1”-2”) diameter

• Easy read scale indicates the air flow and allows adjustment to optimum efficiency
• Provides smoother and better acceleration
• Carbalancer can be adjusted to fit most carburettors
• Easy to follow instructions

The user manual for the Gunson Carbalancer, in English, can be downloaded HERE.

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

• Superior resolution to dial type gauges
• Easily read scale
• Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
• Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
• Stainless steel columns indicate vacuum
• No calibration or set-up required
• High impact plastic casing and scale tubes - no glass
• Dampers supplied to reduce fluctuations
• Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

4 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

• Superior resolution to dial type gauges
• Easy to read scale
• Comes complete with 4 x 5 mm and 4 x 6 mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
• Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
• Stainless steel columns indicate vacuum
• No calibration or set-up required
• High impact plastic casing and scale tubes - no glass
• Dampers supplied to reduce fluctuations
• Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Also fits the Weber DCOE series carburettors and Solex ADDHE.

Synchrometer airflow meter for various carburetors.

Pushes into the trumpet / ram pipe / velocity stack or throat to measure the airflow to enable you to balance multiple carburettors.

• Instructions included
• The original genuine high quality German made product
• Can be used for all Weber DCOE and IDF and Dellorto DHLA, DRLA carbs with round intakes or trumpets
• Can also be used with motorcycle carburetors with round intakes

  Total length of unit 121mm

  Rubber cone dimensions:
  Small end diameter 40mm
  Large end diameter 55mm
  Length of cone 36mm