Dellorto PHM Carburetor Parts
Dellorto PHM Carburetor Parts

Dellorto PHM Parts

Dellorto PHM Carburetor Parts.

On this page you will find all currently available parts for the Dellorto PHM range carburetors.

Click HERE for an exploded view drawing of the Dellorto PHM.

The numbers in the drawing correspond to the numbers in brackets at the beginning of the article description.

Click HERE for instructions on how to set the float level of the Dellorto PHM.

Click HERE for the specifications of the K series needles used on these carburetors.

We are still very much expanding our parts offerings for these carburetors so please contact us by email if the part that you are looking for is not yet listed.

Dellorto PHM Carburetor Parts

!
8530
(2) K Series needle for Dellorto PHM carburetors

(2) K Series needle for Dellorto PHM carburetors

K-series needle for the Dellorto PHM carburetors.

We only supply original Dellorto needles, marked with the famous diamond-shaped "Inc" logo.

In stock in version:

  • K1
  • K2
  • K3
  • K4
  • K9
  • K13
  • K31
  • K51

Can be supplied in virtually any other version but please contact us by email for that.

Required quantity per carburettor: 1

This is item number 2 in the drawing.

Click HERE for the specifications of the K series needles used on these carburettors.

(2) K Series needle for Dellorto PHM carburetors

8540
(3) AB Series Atomizer for Dellorto PHM carburetors

(3) AB Series Atomizer for Dellorto PHM carburetors

AB-series atomizer for the Dellorto PHM carburetors.

We only supply original Dellorto atomisers, marked with the famous diamond-shaped "Inc" logo.

In stock in version:

  • AB262
  • AB264
  • AB265
  • AB266
  • AB268

Can be supplied in virtually any other version but please contact us by email for those.

Required quantity per carburettor: 1

This is item number 3 in the drawing.

(3) AB Series Atomizer for Dellorto PHM carburetors

12599
(3) DR Series Atomizer for Dellorto PHM carburetors

(3) DR Series Atomizer for Dellorto PHM carburetors

DR-series atomizer for the Dellorto PHM carburetors.

This is basically a 4-stroke atomiser.

We only supply original Dellorto needles, marked with the famous diamond-shaped "Inc" logo.

In stock in version:

  • DR266
  • DR270

Can be supplied in virtually any other version but please contact us by email for those.

Required quantity per carburettor: 1

This is item number 3 in the drawing.

(3) DR Series Atomizer for Dellorto PHM carburetors

9542
(3) Bush for DR Series Atomizer for Dellorto PHM carburetors

(3) Bush for DR Series Atomizer for Dellorto PHM carburetors

Atomiser Bush for Dellorto PHM carburetors.

This bush is a push-fit into the body of the carburettor and is the part in which the atomiser screws.

It is specific for the DR-Series 4-Stroke Atomisers.

Required quantity per carburettor: 1

This is item is NOT in the drawing but is generally considered to be part of number 3 in the drawing.

(3) Bush for DR Series Atomizer for Dellorto PHM carburetors

6413
(5) Main jet for Dellorto PHM carburetors

(5) Main jet for Dellorto PHM carburetors

Main jet for the Dellorto PHM carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

In stock in sizes:

  • 52
  • 54
  • 56
  • 58
  • 60
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 105
  • 108
  • 110
  • 115
  • 116
  • 118
  • 120
  • 122
  • 124
  • 125
  • 126
  • 130
  • 135
  • 140
  • 145
  • 150
  • 155
  • 160
  • 165
  • 170
  • 172
  • 175
  • 180
  • 182
  • 185
  • 190
  • 195
  • 200
  • 205
  • 210

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 5 in the drawing.

(5) Main jet for Dellorto PHM carburetors

1486
(6) Idle Jet for Dellorto PHM carburetors

(6) Idle Jet for Dellorto PHM carburetors

Factory original idle jet for the Dellorto PHM carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available from our stock in sizes:

  • 33
  • 35
  • 40
  • 45
  • 48
  • 50
  • 53
  • 55
  • 57
  • 58
  • 60
  • 62
  • 65
  • 67
  • 72
  • 80
  • 82
  • 84
  • 86
  • 88
  • 90
  • 91
  • 92
  • 95
  • 98
  • 100
  • 108
  • 110
  • 112
  • 118
  • 120

Most other sizes are available on special order. Please contact us by email with your exact requirements.

Required quantity per carburetor: 1

This is item number 6 in the drawing.

(6) Idle Jet for Dellorto PHM carburetors

7746
(7) Choke or Starter Jet for Dellorto PHM carburetors

(7) Choke or Starter Jet for Dellorto PHM carburetors

Choke (or starter) jet for the Dellorto PHM carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available from stock in size:

  • 45
  • 50
  • 55
  • 60
  • 65
  • 70
  • 75
  • 80
  • 85
  • 90
  • 100

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 7 in the drawing.

(7) Choke or Starter Jet for Dellorto PHM carburetors

7851
(8) Pump Jet for Dellorto PHM carburetors

(8) Pump Jet for Dellorto PHM carburetors

Pump jet for the Dellorto PHM carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available in sizes:

  • 30
  • 33
  • 35
  • 38
  • 40
  • 42
  • 45
  • 48
  • 50
  • 55
  • 60

Required quantity per carburetor: 1

This is item number 8 in the drawing.

(8) Pump Jet for Dellorto PHM carburetors

NV
(9) Genuine Viton-Tipped Needle Valve Assembly for Dellorto PHM carburetors

(9) Genuine Viton-Tipped Needle Valve Assembly for Dellorto PHM carburetors

Dellorto needle valve, seat and fiber washer for the PHM carburetors.

Genuine Dellorto part, Viton-tipped!

Only genuine Dellorto needles are marked with the diamond shaped "Inc" logo!

Available in size:

  • 150
  • 170
  • 200
  • 225
  • 250
  • 270
  • 300
  • 350
  • 400

Required quantity per carburettor: 1

This is item number 9 in the drawing.

(9) Genuine Viton-Tipped Needle Valve Assembly for Dellorto PHM carburetors

7450
(10) Double Float for Dellorto PHM carburetors

(10) Double Float for Dellorto PHM carburetors

This is the, double, float for the Dellorto PHM carburetors.

Originally, these came only in the early style, black, version with metal linking arm but these are being phased out in favor of the, new, white version.

Please choose the replacement for your defective float according to the part-number on your original.

Available in the following versions:

  • 7450.1 8.5 gram white - replaces 7450.1 10 gram black
  • 7450.2 12.5 gram white - replaces 7450.2 14 gram black
  • 7450.3 7.5 gram black (only 1 left in stock!)
  • 7450.3 6,5 gram white - replaces 7450.3 7.5 gram black

Required quantity per carburetor: 1

This is item number 10 in the drawing.

(10) Double Float for Dellorto PHM carburetors

6429
(11) Screw for DOMED Top Cover on Dellorto PHM carburetors

(11) Screw for DOMED Top Cover on Dellorto PHM carburetors

Screw for the DOMED top cover of the Dellorto PHM carburetors.

Required quantity per carburetor: 2

This is item number 11 in the drawing.

 

 

(11) Screw for DOMED Top Cover on Dellorto PHM carburetors

8826
(13) Top Cover Gasket for Dellorto PHM carburetors with a DOMED top

(13) Top Cover Gasket for Dellorto PHM carburetors with a DOMED top

Paper gasket to seal the top cover on Dellorto PHM carburetors with a domed top.

Required quantity number per carburettor: 1

This is item number 13 in the drawing.

 

(13) Top Cover Gasket for Dellorto PHM carburetors with a DOMED top

8542
(14) Screw for Dellorto PHM carburetors

(14) Screw for Dellorto PHM carburetors

Screw / Bolt that secures the FLAT top cover as well as the lower top casting of the DOMED top Dellorto PHM series carburetors.

Required quantity per carburettor: 2

This is item number 14 in the drawing.

 

 

 

(14) Screw for Dellorto PHM carburetors

8535
(19) Pump Arm Pin for Dellorto PHM carburetors with metal top

(19) Pump Arm Pin for Dellorto PHM carburetors with metal top

Pump arm pin for the Dellorto PHM carburetors with a metal / alloy top.

Please note that there TWO versions of this pin which are NOT interchangeable!
The difference is in the material of the "lower top casting", plastic vs. metal, number 16 in the drawing.
This particular pin is for the metal top.

Required quantity number per carburettor: 1

This is item number 19 in the drawing.

(19) Pump Arm Pin for Dellorto PHM carburetors with metal top

10924
(19) Pump Arm Pin for Dellorto PHM carburetors with plastic top

(19) Pump Arm Pin for Dellorto PHM carburetors with plastic top

Pump arm pin for the Dellorto PHM carburetors with a plastic top.

Please note that there TWO versions of this pin which are NOT interchangeable!
The difference is in the material of the "lower top casting", plastic vs. metal, number 16 in the drawing.
This particular pin is for the plastic top.

Required quantity number per carburettor: 1

This is item number 19 in the drawing.

(19) Pump Arm Pin for Dellorto PHM carburetors with plastic top

9596
(25) Needle Circlip for Dellorto PHM carburetors

(25) Needle Circlip for Dellorto PHM carburetors

Circlip to secure the needle on the Dellorto PHM carburetors with a domed top.

Required quantity per carburetor: 1

This is item number 25 in the drawing.

 

 

(25) Needle Circlip for Dellorto PHM carburetors

4957
(34) Spring Washer for Dellorto PHM carburetors

(34) Spring Washer for Dellorto PHM carburetors

Spring Washer for the throttle cable support on the Dellorto PHM carburetors.

Required quantity per carburetor: 1

This is item number 34 in the drawing.

 

 

(34) Spring Washer for Dellorto PHM carburetors

5011
(38) Spring Washer for Dellorto PHM carburetors

(38) Spring Washer for Dellorto PHM carburetors

Spring Washer for the cable arm of the Dellorto PHM carburetors.

Required quantity per carburetor: 1

This is item number 38 in the drawing.

 

 

(38) Spring Washer for Dellorto PHM carburetors

7415
(42) Pump Arm Spring for Dellorto PHM carburetors

(42) Pump Arm Spring for Dellorto PHM carburetors

Pump arm spring for the Dellorto PHM carburetors.

Return spring for the pump arm.

Required quantity number per carburettor: 1

This is item number 42 in the drawing.

 

 

 

(42) Pump Arm Spring for Dellorto PHM carburetors

8426
(43) Pump Arm for Dellorto PHM carburetors

(43) Pump Arm for Dellorto PHM carburetors

Pump arm for the Dellorto PHM carburetors.

Actuator arm for the pump mechanism.

Required quantity number per carburettor: 1

This is item number 43 in the drawing.

 

 

 

(43) Pump Arm for Dellorto PHM carburetors

9330
(44) 40 Degree Cable Elbow for Dellorto PHM carburetors

(44) 40 Degree Cable Elbow for Dellorto PHM carburetors

40 degrees cable elbow for the Dellorto PHM carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburetor: 1

This is item number 44 in the drawing.

 

(44) 40 Degree Cable Elbow for Dellorto PHM carburetors

10854
(44) 50 Degree Cable Elbow for Dellorto PHM carburetors

(44) 50 Degree Cable Elbow for Dellorto PHM carburetors

50 degrees cable elbow for the Dellorto PHM carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburetor: 1

This is item number 44 in the drawing.

 

(44) 50 Degree Cable Elbow for Dellorto PHM carburetors

3600
(44) 70 Degree Cable Elbow for Dellorto PHM carburetors

(44) 70 Degree Cable Elbow for Dellorto PHM carburetors

70 degrees cable elbow for the Dellorto PHM carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburetor: 1

This is item number 44 in the drawing.

 

(44) 70 Degree Cable Elbow for Dellorto PHM carburetors

3698
(44) 90 Degree Cable Elbow for Dellorto PHM carburetors

(44) 90 Degree Cable Elbow for Dellorto PHM carburetors

90 degrees cable elbow for the Dellorto PHM carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburetor: 1

This is item number 44 in the drawing.

 

(44) 90 Degree Cable Elbow for Dellorto PHM carburetors

1691
Lock Nut for Cable Elbow on Dellorto carburetors

Lock Nut for Cable Elbow on Dellorto carburetors

This lock nut is used on a wide variety of Dellorto carburetors to secure the cable elbow into the top cover.

Required quantity per elbow: 1

This item is usually NOT depicted in the drawing.

 

 

 

Lock Nut for Cable Elbow on Dellorto carburetors

1692
(45) Lock nut for Cable Adjuster on Dellorto PHM carburetors

(45) Lock nut for Cable Adjuster on Dellorto PHM carburetors

This is the locknut that secures the setting on the throttle cable for the Dellorto PHM carburetors.

Required quantity per carburetor: 1

This is item number 45 in the drawing.

 

(45) Lock nut for Cable Adjuster on Dellorto PHM carburetors

1481
(46) Cable Adjuster for Dellorto PHM carburetors

(46) Cable Adjuster for Dellorto PHM carburetors

Cable adjuster for the Dellorto PHM carburetors.

Fits an outer cable with an external diameter of 6.75 mm.

This cable adjuster uses Lock Nut 1692 to secure its setting.
For your convenience, you can order this lock nut right along with this adjuster by simply selecting it through the drop box above.

Required quantity per carburetor: 1

This is item number 46 in the drawing.

 

(46) Cable Adjuster for Dellorto PHM carburetors

1476A
(47) Rubber Cable Boot for Dellorto PHM carburetors

(47) Rubber Cable Boot for Dellorto PHM carburetors

Rubber cable cap for both the choke cable adjuster as well as the throttle cable adhuster on the Dellorto PHM carburetors.

Required quantity per carburettor: depending on your set-up 1 x for choke cable + 1 x for throttle cable.

This is item number 47 in the drawing.

(47) Rubber Cable Boot for Dellorto PHM carburetors

1104
(48) Cable Adjuster for Dellorto PHM carburetors

(48) Cable Adjuster for Dellorto PHM carburetors

Cable adjuster for the Dellorto PHM carburetors.

This cable adjuster sometimes uses Lock Nut 1691 to secure its setting.
For your convenience, you can order this lock nut right along with this adjuster by simply selecting it through the drop box above.

Required quantity per carburetor: depending on your set-up

This is item number 48 in the drawing.

(48) Cable Adjuster for Dellorto PHM carburetors

1691
(49) Lock Nut for Choke Cable Adjuster on Dellorto PHM carburetors

(49) Lock Nut for Choke Cable Adjuster on Dellorto PHM carburetors

This is the locknut that secures the setting on the choke cable of the Dellorto PHM carburetors.

Please note that this lock nut fits cable adjuster number 48 in the drawing ONLY!

Required quantity per carburettor: 1

This is item number 49 in the drawing.

 

(49) Lock Nut for Choke Cable Adjuster on Dellorto PHM carburetors

3133
(51) Choke Return Spring for Dellorto PHM carburetors

(51) Choke Return Spring for Dellorto PHM carburetors

Choke return spring for the Dellorto PHM series carburetors.

Required quantity per carburettor: 1

This is item number 51 in the drawing.

 

 

(51) Choke Return Spring for Dellorto PHM carburetors

3238
(52) Choke Piston for Dellorto PHM carburetors

(52) Choke Piston for Dellorto PHM carburetors

Choke piston for the Dellorto PHM series carburetors.

Required quantity per carburettor: 1

This is item number 52 in the drawing.

 

 

 

 

(52) Choke Piston for Dellorto PHM carburetors

11650
(53) Choke Body Screw for Dellorto PHM carburetors - Long

(53) Choke Body Screw for Dellorto PHM carburetors - Long

Screw to secure the choke body on the Dellorto PHM series carburetors.

This is the long version which is used when the choke is combined with a spacer.

For use without the spacer, please use screw number 54 on the drawing.

Required quantity per carburettor: 1

This is item number 53 in the drawing.

(53) Choke Body Screw for Dellorto PHM carburetors - Long

8711
(54) Choke Body Screw for Dellorto PHM carburetors - Short

(54) Choke Body Screw for Dellorto PHM carburetors - Short

Screw to secure the choke body on the Dellorto PHM series carburetors.

This is the short version which is used when no spacer is used.

For use with the spacer, please use screw number 53 on the drawing.

Required quantity per carburettor: 1

This is item number 54 in the drawing.

(54) Choke Body Screw for Dellorto PHM carburetors - Short

7449
(58) Mixture screw for Dellorto PHM carburetors

(58) Mixture screw for Dellorto PHM carburetors

Mixture screw for the Dellorto PHM carburetors.

Total length: 33 mm

Tip length: 2.5 mm

Parallel shaft length: 17.4 mm

Please note that this version is NOT suitable for the Cagiva Mito.

Moto Guzzi uses a shorter (29 mm) version.

Required quantity per carburetor: 1

This is item number 58 in the drawing.

(58) Mixture screw for Dellorto PHM carburetors

9336
(59) Mixture screw spring for Dellorto PHM carburetors

(59) Mixture screw spring for Dellorto PHM carburetors

Mixture screw spring for suitable for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 59 in the drawing.

 

 

(59) Mixture screw spring for Dellorto PHM carburetors

8260
(60) Mixture screw spring washer for Dellorto PHM carburetors

(60) Mixture screw spring washer for Dellorto PHM carburetors

Washer that keeps the mixture screw spring in place on the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 60 in the drawing.

 

(60) Mixture screw spring washer for Dellorto PHM carburetors

8678
(61) O-Ring for mixture screw on Dellorto PHM carburetors

(61) O-Ring for mixture screw on Dellorto PHM carburetors

Viton (rubber) O-Ring for mixture screw on Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 61 in the drawing.

 

 

(61) O-Ring for mixture screw on Dellorto PHM carburetors

10747
(62) Pump jet holder for Dellorto PHM carburetors

(62) Pump jet holder for Dellorto PHM carburetors

Pump jet holder for Dellorto PHM carburetors.

Required quantity per carburetor: 1

This is item number 62 in the drawing.

 

 

(62) Pump jet holder for Dellorto PHM carburetors

6426
(63) Fiber Ring for Dellorto PHM carburetors

(63) Fiber Ring for Dellorto PHM carburetors

Fiber ring for the pump jet holder for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 63 in the drawing.

 

 

(63) Fiber Ring for Dellorto PHM carburetors

6173
(64) O-ring for Dellorto PHM carburetors

(64) O-ring for Dellorto PHM carburetors

O-ring for the Dellorto PHM carburetors.

This o-ring is used on both the pump jet and choke jet.

Required quantity per carburettor: 1

This is item number 64 in the drawing.

 

(64) O-ring for Dellorto PHM carburetors

4670
(66) Throttle stop spring for Dellorto PHM carburetors

(66) Throttle stop spring for Dellorto PHM carburetors

Throttle stop screw spring for Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 66 in the drawing.

 

 

(66) Throttle stop spring for Dellorto PHM carburetors

4650
(67) Throttle Stop Washer for Dellorto PHM carburetors

(67) Throttle Stop Washer for Dellorto PHM carburetors

Throttle Stop Washer for Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 67 in the drawing.

 

 

(67) Throttle Stop Washer for Dellorto PHM carburetors

7540
(68) Throttle Stop Screw O ring for Dellorto PHM carburetors

(68) Throttle Stop Screw O ring for Dellorto PHM carburetors

Viton O-ring to seal the throttle stop screw on the Dellorto PHM carburetors.

Required quantity per carburetor: 1

This is item number 68 in the drawing.

 

 

(68) Throttle Stop Screw O ring for Dellorto PHM carburetors

8598
(71) O-ring for the Pump Adjustment Screw on Dellorto PHM carburetors

(71) O-ring for the Pump Adjustment Screw on Dellorto PHM carburetors

O-ring for the Adjustment Screw of the Pump of the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 71 in the drawing.

 

 

 

(71) O-ring for the Pump Adjustment Screw on Dellorto PHM carburetors

7626
(75) Pump Diaphragm Spring for Dellorto PHM carburetors

(75) Pump Diaphragm Spring for Dellorto PHM carburetors

Pump Diaphragm Spring for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 75 in the drawing.

 

 

(75) Pump Diaphragm Spring for Dellorto PHM carburetors

8555
(76) Pump Diaphragm for Dellorto PHM carburetors

(76) Pump Diaphragm for Dellorto PHM carburetors

Pump Diaphragm for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 76 in the drawing.

 

 

(76) Pump Diaphragm for Dellorto PHM carburetors

9278
(77) Pump Diaphragm Gasket for Dellorto PHM carburetors

(77) Pump Diaphragm Gasket for Dellorto PHM carburetors

Pump Diaphragm Gasket for the Dellorto PHM carburetors.

This gasket is fitted in between the the diaphragm and the carburetor body.

Required quantity per carburettor: 1

This is item number 77 in the drawing.

 

(77) Pump Diaphragm Gasket for Dellorto PHM carburetors

8885 - 8552
(78) Main Jet Holder for Dellorto PHM carburetors

(78) Main Jet Holder for Dellorto PHM carburetors

This is the main jet holder for the Dellorto PHM carburetors.

Please note that there are TWO different versions available which are NOT interchangeable!

The available versions are:

  1. 8885 - 17 MM tall
  2. 8552 - 20 MM tall

Required quantity per carburettor: 1

This is item number 78 in the drawing.

(78) Main Jet Holder for Dellorto PHM carburetors

6109
(81) Banjo Fuel Filter for Dellorto PHM carburetors

(81) Banjo Fuel Filter for Dellorto PHM carburetors

Special fuel filter to fit the banjo fuel bolt of the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 81 in the drawing.

 

 

(81) Banjo Fuel Filter for Dellorto PHM carburetors

9250
(82) 8 mm Single Plastic Fuel Inlet Banjo for Dellorto PHM carburetors

(82) 8 mm Single Plastic Fuel Inlet Banjo for Dellorto PHM carburetors

Plastic fuel inlet banjo for the Dellorto PHM carburetors for 8 mm fuel lines.

This banjo uses banjo bolt number 4568 but NO fiber washer.

For your convenience, you can order this inlet banjo complete with banjo bolt or without it.

Required quantity per carburettor: 1

This is item number 82 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(82) 8 mm Single Plastic Fuel Inlet Banjo for Dellorto PHM carburetors

6273
(82) 8 mm Single Metal Fuel Inlet Banjo for Dellorto PHM carburetors

(82) 8 mm Single Metal Fuel Inlet Banjo for Dellorto PHM carburetors

Metal fuel inlet banjo for the Dellorto PHM carburetors for 8 mm fuel lines.

This banjo uses fiber washer number 4052 and bolt number 4568.

For your convenience, you can order this inlet banjo complete with fiber washer and banjo bolt or without simply without these extras.

Required quantity per carburettor: 1

This is item number 82 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(82) 8 mm Single Metal Fuel Inlet Banjo for Dellorto PHM carburetors

6517
(82) 8 mm Angled Metal Fuel Inlet Banjo for Dellorto PHM carburetors

(82) 8 mm Angled Metal Fuel Inlet Banjo for Dellorto PHM carburetors

Metal fuel inlet banjo for the Dellorto PHM carburetors with the fuel union under an angle of some 45 degrees (see photo) for 8 mm fuel lines.

Please note that there are two version of this inlet banjo: a plastic one and this metal version.

This banjo uses fiber washer number 4052 and bolt number 4568.

For your convenience, you can order this inlet banjo complete with fiber washer and banjo bolt or without simply without these extras.

Required quantity per carburettor: 1

This is item number 82 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(82) 8 mm Angled Metal Fuel Inlet Banjo for Dellorto PHM carburetors

7890
(82) 8 mm Double Fuel Inlet Banjo for Dellorto PHM carburetors

(82) 8 mm Double Fuel Inlet Banjo for Dellorto PHM carburetors

This is the, TWIN, metal fuel inlet banjo for the Dellorto PHM carburetors for 8 mm fuel lines.

Please note that there is also a SINGLE metal version and a SINGLE plastic version in various connection sizes.

This double metal version which uses fiber washer number 4052.

This double metal version which uses banjo bolt 4568.

For your convenience, you can order this inlet banjo complete with fiber washer and banjo bolt or simply without these extras.

Required quantity per carburettor: 1

This is item number 82 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(82) 8 mm Double Fuel Inlet Banjo for Dellorto PHM carburetors

4568
(83) Long Fuel Banjo Bolt for Dellorto PHM carburetors

(83) Long Fuel Banjo Bolt for Dellorto PHM carburetors

Fuel banjo bolt for the Dellorto PHM carburetors with 8 mm pipe fitting banjos only.

This bolt has an overall length of some 21 mm with a shaft length of approximately 17.5 mm and will NOT fit the banjos for 6 mm fuel lines.

Required quantity per carburettor: 1

This is item number 83 in the drawing.

 

 

(83) Long Fuel Banjo Bolt for Dellorto PHM carburetors

8557
(84) Pump Non-Return Valve for Dellorto PHM carburetors

(84) Pump Non-Return Valve for Dellorto PHM carburetors

Pump Non-Return Valve for Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 84 in the drawing.

 

 

 

 

(84) Pump Non-Return Valve for Dellorto PHM carburetors

6288
(85) Fiber Ring for the Needle Valve on the Dellorto PHM carburetors

(85) Fiber Ring for the Needle Valve on the Dellorto PHM carburetors

Fiber ring to seal the needle valve on the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 85 in the drawing.

 

 

(85) Fiber Ring for the Needle Valve on the Dellorto PHM carburetors

7451
(86) Float Bowl O-Ring for Dellorto PHM carburetors

(86) Float Bowl O-Ring for Dellorto PHM carburetors

Float bowl o-ring / rubber gasket for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 86 in the drawing.

 

 

(86) Float Bowl O-Ring for Dellorto PHM carburetors

7346
(87) Float Pivot Pin for Dellorto PHM carburetors

(87) Float Pivot Pin for Dellorto PHM carburetors

Standard float pivot pin for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 87 in the drawing.

 

 

(87) Float Pivot Pin for Dellorto PHM carburetors

4057
(89) 14 and 17 mm Float Bowl Nut Seal for Dellorto PHM carburetors

(89) 14 and 17 mm Float Bowl Nut Seal for Dellorto PHM carburetors

Float bowl nut seal for the Dellorto PHM carburetors.

Fits the 14 and 17 mm varieties of that special nut (number 90 in the drawing):

Required quantity per carburettor: 1

This is item number 89 in the drawing.

(89) 14 and 17 mm Float Bowl Nut Seal for Dellorto PHM carburetors

8551
(90) 14 mm Float Bowl Nut for Dellorto PHM carburetors

(90) 14 mm Float Bowl Nut for Dellorto PHM carburetors

Special Nut / Drain Plug to secure the float bowl on the Dellorto PHM carburetors.

Please note: there is a total of 3 different nuts available which are NOT interchangeable.

These are most easily identified by the spanner size needed for them.

This particular versions requires a 14 mm spanner.

This nut uses Fiber Seal 4057 to seal against the float chamber.

For your convenience, you can order a new fiber seal right along with the nut by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 90 in the drawing.

(90) 14 mm Float Bowl Nut for Dellorto PHM carburetors

9676
(90) 17 mm Float Bowl Nut for Dellorto PHM carburetors

(90) 17 mm Float Bowl Nut for Dellorto PHM carburetors

Special Nut to secure the float bowl on the Dellorto PHM carburetors.

Please note: there is a total of 3 different nuts available which are NOT interchangeable.

These are most easily identified by the spanner size needed for them.

This particular versions requires a 17 mm spanner.

This nut uses Fiber Seal 4057 to seal against the float chamber.

For your convenience, you can order a new fiber seal right along with the nut by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 90 in the drawing.

(90) 17 mm Float Bowl Nut for Dellorto PHM carburetors

4570
Fiber Seal for Float Bowl Plug on Dellorto PHM carburetors

Fiber Seal for Float Bowl Plug on Dellorto PHM carburetors

Fiber seal for the float bowl nut with Drain Facility on the Dellorto PHM series carburetors.

Is used on float bowl nut 9973 with drain plug 9812.

Required quantity per carburettor when equipped with appropriate drain plug: 1

This item number is NOT in the drawing.

Fiber Seal for Float Bowl Plug on Dellorto PHM carburetors

2778
(89) 21 mm Float Bowl Nut Seal for Dellorto PHM carburetors

(89) 21 mm Float Bowl Nut Seal for Dellorto PHM carburetors

Float bowl nut seal for the Dellorto PHM carburetors.

Fits the 21 mm varieties of that special nut (number 90 in the drawing):

Required quantity per carburettor: 1

This is item number 89 in the drawing.

(89) 21 mm Float Bowl Nut Seal for Dellorto PHM carburetors

10238
(90) 21 mm Float Bowl Nut for Dellorto PHM carburetors

(90) 21 mm Float Bowl Nut for Dellorto PHM carburetors

Special Nut to secure the float bowl on the Dellorto PHM carburetors.

Please note: there is a total of 4 different nuts available which are NOT interchangeable.

These are most easily identified by the spanner size needed for them.

This particular versions requires a 21 mm spanner.

This nut uses Fiber Seal 2778 to seal against the float chamber.

For your convenience, you can order a new fiber seal right along with the nut by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 90 in the drawing.

(90) 21 mm Float Bowl Nut for Dellorto PHM carburetors

52520
(91) Service Kit for Dellorto PHM A B N and V carburetors

(91) Service Kit for Dellorto PHM A B N and V carburetors

Factory-original service kit for the Dellorto PHM carburetors with suffix A, B, N and V with a flat, round, top cover.

The PHM series comes with two different top covers which are illustrated here:

This service kit contains all the necessary gaskets, o-rings, fiber rings and a rubber cable boot as per the product photo.

Required quantity per carburettor: 1

This is item number 91 in the drawing.

Please note:
There is a total of 4 (four!) different service kits available for the Dellorto PHM series whereby the differences are determined by the suffix that you will find on the body of your carburettor and the shape of the top cover. These kits are NOT interchangeable!

Suffix A - Flat Top: 52520
Suffix B - Flat Top: 52520
Suffix C - Domed Top: 52545
Suffix D - Domed Top: 52545
Suffix H - Flat Top: 52544
Suffix L - Flat Top: 52544
Suffix M - Flat Top: 52544
Suffix N - Flat Top: 52520
Suffix N - Domed Top: 52560
Suffix P - Flat Top: 52544
Suffix R - Flat Top: 52544
Suffix S - Flat Top: 52544
Suffix T - Flat Top: 52544
Suffix V - Flat Top: 52520
Suffix Z - Flat Top: 52544

(91) Service Kit for Dellorto PHM A B N and V carburetors

52520
(91) Service Kit for Dellorto PHM B Carburetors for BMW 90S

(91) Service Kit for Dellorto PHM B Carburetors for BMW 90S

Factory-original service kit for the Dellorto PHM38BS and PHM38BD as used on the BMW 90S.

The PHM series comes with two different top covers which are illustrated here:

This service kit is specifically for the flat top version and contains all the necessary gaskets, o-rings, fiber rings and a rubber cable boot as per the product photo.

Required quantity per carburettor: 1

This is item number 91 in the drawing of the PHM.
Please click HERE for that drawing.

(91) Service Kit for Dellorto PHM B Carburetors for BMW 90S

52545
(91) Service Kit for Dellorto PHM C and D carburetors

(91) Service Kit for Dellorto PHM C and D carburetors

Factory-original service kit for the Dellorto PHM carburetors with suffix C and D with a domed top cover.

The PHM series comes with two different top covers which are illustrated here:

This service kit contains all the necessary gaskets, o-rings and fiber rings as per the product photo.

Required quantity per carburettor: 1

This is item number 91 in the drawing.

Please note:
There is a total of 4 (four!) different service kits available for the Dellorto PHM series whereby the differences are determined by the suffix that you will find on the body of your carburettor and the shape of the top cover. These kits are NOT interchangeable!

Suffix A - Flat Top: 52520
Suffix B - Flat Top: 52520
Suffix C - Domed Top: 52545
Suffix D - Domed Top: 52545
Suffix H - Flat Top: 52544
Suffix L - Flat Top: 52544
Suffix M - Flat Top: 52544
Suffix N - Flat Top: 52520
Suffix N - Domed Top: 52560
Suffix P - Flat Top: 52544
Suffix R - Flat Top: 52544
Suffix S - Flat Top: 52544
Suffix T - Flat Top: 52544
Suffix V - Flat Top: 52520
Suffix Z - Flat Top: 52544

(91) Service Kit for Dellorto PHM C and D carburetors

52544
(91) Service Kit for Dellorto PHM H L M P R T S and Z carburetors

(91) Service Kit for Dellorto PHM H L M P R T S and Z carburetors

Factory-original service kit for the Dellorto PHM carburetors with suffix H, L, M, P, R, T, S and Z with a flat, round, top cover.

The PHM series comes with two different top covers which are illustrated here:

This service kit contains all the necessary gaskets, o-rings and fiber rings as per the product photo.

Required quantity per carburettor: 1

This is item number 91 in the drawing.

Please note:
There is a total of 4 (four!) different service kits available for the Dellorto PHM series whereby the differences are determined by the suffix that you will find on the body of your carburettor and the shape of the top cover. These kits are NOT interchangeable!

Suffix A - Flat Top: 52520
Suffix B - Flat Top: 52520
Suffix C - Domed Top: 52545
Suffix D - Domed Top: 52545
Suffix H - Flat Top: 52544
Suffix L - Flat Top: 52544
Suffix M - Flat Top: 52544
Suffix N - Flat Top: 52520
Suffix N - Domed Top: 52560
Suffix P - Flat Top: 52544
Suffix R - Flat Top: 52544
Suffix S - Flat Top: 52544
Suffix T - Flat Top: 52544
Suffix V - Flat Top: 52520
Suffix Z - Flat Top: 52544

(91) Service Kit for Dellorto PHM H L M P R T S and Z carburetors

52560
(91) Service Kit for Dellorto PHM N carburetors

(91) Service Kit for Dellorto PHM N carburetors

Factory-original service kit for the Dellorto PHM carburetors with suffix N with a domed top cover.

The PHM series comes with two different top covers which are illustrated here:

This service kit contains all the necessary gaskets, o-rings and fiber rings as per the product photo.

Required quantity per carburettor: 1

This is item number 91 in the drawing.

Please note:
There is a total of 4 (four!) different service kits available for the Dellorto PHM series whereby the differences are determined by the suffix that you will find on the body of your carburettor and the shape of the top cover. These kits are NOT interchangeable!

Suffix A - Flat Top: 52520
Suffix B - Flat Top: 52520
Suffix C - Domed Top: 52545
Suffix D - Domed Top: 52545
Suffix H - Flat Top: 52544
Suffix L - Flat Top: 52544
Suffix M - Flat Top: 52544
Suffix N - Flat Top: 52520
Suffix N - Domed Top: 52560
Suffix P - Flat Top: 52544
Suffix R - Flat Top: 52544
Suffix S - Flat Top: 52544
Suffix T - Flat Top: 52544
Suffix V - Flat Top: 52520
Suffix Z - Flat Top: 52544

(91) Service Kit for Dellorto PHM N carburetors

4052
(92) Banjo Bolt Fiber Washer for Dellorto PHM carburetors

(92) Banjo Bolt Fiber Washer for Dellorto PHM carburetors

Banjo bolt fiber washer for the Dellorto PHM carburetors.

Required quantity per carburettor: 1

This is item number 92 in the drawing.

 

 

(92) Banjo Bolt Fiber Washer for Dellorto PHM carburetors

PHMTRUMPET36/G
(94) 36 mm Trumpet with Gauze for Dellorto PHM carburetors

(94) 36 mm Trumpet with Gauze for Dellorto PHM carburetors

Trumpet with Gauze for Dellorto PHM carburetors.

Machined from 1 piece aluminum in Germany!

Fitted with fixed, coarse, gauze.

Trumpet Length: 36 mm.

Will fit PHM carburettors with a 52 mm male intake thread.

The gauze adds approximately 18 mm to the trumpet length.

The diameter of the flare at the gauze end is circa 75 mm.

Required quantity per carburettor: 1

This is item number 94 in the drawing.

(94) 36 mm Trumpet with Gauze for Dellorto PHM carburetors

PHMTRUMPET45/G
(94) 45 mm Trumpet with Gauze for Dellorto PHM carburetors

(94) 45 mm Trumpet with Gauze for Dellorto PHM carburetors

Trumpet with Gauze for Dellorto PHM carburetors.

Machined from 1 piece aluminum in Germany!

Fitted with fixed, coarse, gauze.

Trumpet Length: 45 mm.

Will fit PHM carburettors with a 52 mm male intake thread.

The gauze adds approximately 18 mm to the trumpet length.

The diameter of the flare at the gauze end is circa 75 mm.

Required quantity per carburettor: 1

This is item number 94 in the drawing.

(94) 45 mm Trumpet with Gauze for Dellorto PHM carburetors

PHMTRUMPET70/G
(94) 70 mm Trumpet with Gauze for Dellorto PHM carburetors

(94) 70 mm Trumpet with Gauze for Dellorto PHM carburetors

Trumpet with Gauze for Dellorto PHM carburetors.

Machined from 1 piece aluminum in Germany!

Fitted with fixed, coarse, gauze.

Trumpet Length: 70 mm.

Will fit PHM carburettors with a 52 mm male intake thread.

The gauze adds approximately 18 mm to the trumpet length.

The diameter of the flare at the gauze end is circa 75 mm.

Required quantity per carburettor: 1

This is item number 94 in the drawing.

(94) 70 mm Trumpet with Gauze for Dellorto PHM carburetors

SlideSpring
(100) Internal Slide Spring for Dellorto PHM carburetors

(100) Internal Slide Spring for Dellorto PHM carburetors

Internal Slide Spring for the Dellorto PHM series carburetors.

Available in 3 settings:

  • Weak: Free length 125 mm, Wire diameter 1.12 mm, Spring diameter 20 mm, Number of turns 19
  • Medium: Free length 132 mm, Wire diameter 1.20 mm, Spring diameter 20 mm, Number of turns 19
  • Strong: Free length 137 mm, Wire diameter 1.25 mm, Spring diameter 20 mm, Number of turns 17

Required quantity per carburettor: 1

This is item number 100 in the drawing.

(100) Internal Slide Spring for Dellorto PHM carburetors

8525
(101) Needle Circlip for Dellorto PHM carburetors

(101) Needle Circlip for Dellorto PHM carburetors

Circlip to secure the needle on Dellorto PHM carburetors with a flat top.

Required quantity per carburettor: 1

This is item number 101 in the drawing.

 

 

 

 

(101) Needle Circlip for Dellorto PHM carburetors

9619
(102) Choke Lever Assembly for Dellorto PHM carburetors

(102) Choke Lever Assembly for Dellorto PHM carburetors

Hand-operated, lever-type- choke mechanism for the Dellorto PHM carburetors.

Can also be used to replace a cable-operated system.

Required quantity per carburettor: 1

This is item number 102 in the drawing.

 

 

(102) Choke Lever Assembly for Dellorto PHM carburetors

15760
(109) Single White plastic float for Dellorto PHM carburetors

(109) Single White plastic float for Dellorto PHM carburetors

Single, white plastic, float for the Dellorto PHM carburetors.

Available in the following versions:

  • 15760.3 - 4.0 grams
  • 15760.4 - 5.2 grams
  • 15760.5 - 3.6 grams

Required quantity per carburettor: 2

This is item number 109 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHM.

(109) Single White plastic float for Dellorto PHM carburetors

9794
(109) Single Black plastic float for Dellorto PHM carburetors

(109) Single Black plastic float for Dellorto PHM carburetors

Single, black plastic, float for the Dellorto PHM carburetors.

Available in the following versions:

  • 9794.1 - 3.5 gram
  • 9794.3 - 3.5 gram
  • 9794.4 - 4.5 gram
  • 9794.5 - 2.8 gram

Required quantity per carburettor: 2

This is item number 109 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHM.

(109) Single Black plastic float for Dellorto PHM carburetors

9679
Brass vacuum take-off adapter for carburetors and manifolds

Brass vacuum take-off adapter for carburetors and manifolds

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Also fits the Weber DCOE series carburettors and Solex ADDHE.

 

Brass vacuum take-off adapter for carburetors and manifolds

9008
Breather Pipe Connection for Dellorto PHM carburetors

Breather Pipe Connection for Dellorto PHM carburetors

This breather pipe connector will fit a wide range of Dellorto carburetors, amongst which the PHM carburetors.

This pipe has 5 mm push fit in the carburettor body and connects to a 3.8 mm internal diameter breather line.

Required quantity per carburetor: 1

This item is NOT shown in the drawing.

Breather Pipe Connection for Dellorto PHM carburetors

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15MM
  • 0.25MM
  • 0.4MM
  • 0.8MM
  • 1.6MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

GREENFUEL8MM-50cm
Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

Italian style clear green fuel line hose with 8 mm inner diameter

gatestextiel8mm
Gates textile covered fuel line hose with 8 mm inner diameter

Gates textile covered fuel line hose with 8 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

Gates textile covered fuel line hose with 8 mm inner diameter

jubilee11-13
11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

PRO805
Sytec Pro-Line in-line fuel filter - 8 mm

Sytec Pro-Line in-line fuel filter - 8 mm

In line fuel filter with cleanable / replaceable filter.

Suitable for 8 mm internal diameter fuel hoses.

Replacement filter elements are available HERE.

Chrome finish.

Toughened glass phial.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

Supplied with 2 Jubilee clips.

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Sytec Pro-Line in-line fuel filter - 8 mm

PRO896
Replacement elements for Sytec in-line fuel filter

Replacement elements for Sytec in-line fuel filter

3 replacement elements for the Sytec Pro-Line in-line fuel filter.

Come complete with new rubber seals.

These elements fit our PRO804 and PRO805 Sytec in-line fuel filters.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

 

 

 

 

Replacement elements for Sytec in-line fuel filter

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

Available from our Stock

DD0906
Dellorto Carburatori Sticker - Large

Dellorto Carburatori Sticker - Large

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 9 x 3 cm (3.54 x 1.2 inches).

This is Number 1 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Large

DD0909
Dellorto Carburatori Sticker - Medium

Dellorto Carburatori Sticker - Medium

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 8 x 4 cm (3.1 x 1.55 inches).

This is Number 2 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Medium

DD0905
Dellorto Carburatori Sticker - Small - Low

Dellorto Carburatori Sticker - Small - Low

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 6 x 2 cm (2.4 x 0.8 inches).

This is Number 3 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Small - Low

Patch
Dellorto Carburatori Sew-On Patch

Dellorto Carburatori Sew-On Patch

Official issue sew-on patch with the Dellorto logo and Italian flag "tricolore" colors.

Measures 12 x 6.5 cm (4.7 x 2.6 inches).

Elaborately embroidered.

 

 

Dellorto Carburatori Sew-On Patch