Dellorto PHF Carburetor Parts
Dellorto PHF Carburetor Parts

Dellorto PHF Parts

Dellorto PHF Carburetor Parts.

On this page you will find parts for the Dellorto PHF range carburetors.

Click HERE for an exploded view drawing of the Dellorto PHF.

The numbers in the drawing correspond to the numbers in brackets at the beginning of the article description.

Click HERE for instructions on how to set the float level of the Dellorto PHF.

Click HERE for the specifications of the K series needles used on these carburetors.

Please click HERE for a brief explanation of the throttle slides as used in these tapered-needle-type carburetors.

We are still very much expanding our parts offerings for these carburetors so please contact us by email if the part that you are looking for is not yet listed.

Dellorto PHF Carburetor Parts

!
8553
(1) Throttle Slide for Dellorto PHF carburetors - early type

(1) Throttle Slide for Dellorto PHF carburetors - early type

This is the early type throttle slide for the Dellorto PHF carburetors.

Please note that there MANY different version of slides available for these carburetors and that choosing the correct one is of the utmost importance.

Please click HERE for a brief explanation of the slides.

Currently available in version 50/1.

Please contact us by email if you require this slide in different versions as not all versions are still available.

Required quantity per carburettor: 1

This is item number 1 in the drawing.

(1) Throttle Slide for Dellorto PHF carburetors - early type

11570
(1) Throttle Slide for Dellorto PHF carburetors

(1) Throttle Slide for Dellorto PHF carburetors

Current-type slide for the Dellorto PHF carburetors.

Original Dellorto.

Please note that there are different versions of this slide.

The main difference is the width of the stop screw ramp.

This is the version where the ramp is 6.2 mm wide.

In stock in version:

  • 60/3

Can be supplied in virtually any other version but please contact us by email for that.

Required quantity per carburettor: 1

This is item number 1 in the drawing.

(1) Throttle Slide for Dellorto PHF carburetors

8530
(2) K Series needle for Dellorto PHF carburetors

(2) K Series needle for Dellorto PHF carburetors

K-series needle for the Dellorto PHF carburetors.

We only supply original Dellorto needles, marked with the famous diamond-shaped "Inc" logo.

In stock in version:

  • K1
  • K2
  • K3
  • K4
  • K9
  • K13
  • K19
  • K29
  • K31
  • K51

Can be supplied in virtually any other version but please contact us by email for that.

Required quantity per carburettor: 1

This is item number 2 in the drawing.

Click HERE for the specifications of the K series needles used on these carburetors.

(2) K Series needle for Dellorto PHF carburetors

8540
(3) AB Series Atomizer for Dellorto PHF carburetors

(3) AB Series Atomizer for Dellorto PHF carburetors

AB-series atomizer for the Dellorto PHF carburetors.

We only supply original Dellorto atomisers, marked with the famous diamond-shaped "Inc" logo.

In stock in version:

  • AB260
  • AB262
  • AB264
  • AB265
  • AB266
  • AB268

Can be supplied in virtually any other version but please contact us by email for that.

Required quantity per carburettor: 1

This is item number 3 in the drawing.

(3) AB Series Atomizer for Dellorto PHF carburetors

6413
(4) Main jet for Dellorto PHF carburetors

(4) Main jet for Dellorto PHF carburetors

Main jet for the Dellorto PHF carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

In stock in sizes:

  • 50
  • 52
  • 54
  • 56
  • 58
  • 60
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 105
  • 108
  • 110
  • 115
  • 116
  • 118
  • 120
  • 122
  • 124
  • 125
  • 126
  • 130
  • 132
  • 135
  • 140
  • 145
  • 150
  • 155
  • 160
  • 165
  • 170
  • 172
  • 175
  • 180
  • 182
  • 185
  • 190
  • 195
  • 200
  • 205
  • 210
  • 215

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 4 in the drawing.

(4) Main jet for Dellorto PHF carburetors

1486
(5) Idle Jet for Dellorto PHF carburetors

(5) Idle Jet for Dellorto PHF carburetors

Factory original idle jet for the Dellorto PHF carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available from our stock in sizes:

  • 33
  • 35
  • 40
  • 45
  • 48
  • 50
  • 53
  • 55
  • 57
  • 58
  • 60
  • 62
  • 65
  • 67
  • 72
  • 80
  • 82
  • 84
  • 86
  • 88
  • 90
  • 91
  • 92
  • 95
  • 98
  • 100
  • 108
  • 110
  • 112
  • 115
  • 118
  • 120

Most other sizes are available on special order. Please contact us by email with your exact requirements.

Required quantity per carburettor: 1

This is item number 5 in the drawing.

(5) Idle Jet for Dellorto PHF carburetors

7746
(6) Choke or Starter Jet for Dellorto PHF carburetors

(6) Choke or Starter Jet for Dellorto PHF carburetors

Choke (or starter) jet for the Dellorto PHF carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available from stock in size:

  • 45
  • 50
  • 55
  • 60
  • 65
  • 70
  • 75
  • 80
  • 85
  • 90
  • 100

Please contact us by email if you require other size(s).

Required quantity per carburettor: 1

This is item number 6 in the drawing.

(6) Choke or Starter Jet for Dellorto PHF carburetors

7851
(7) Pump Jet for Dellorto PHF carburetors

(7) Pump Jet for Dellorto PHF carburetors

Pump jet for the Dellorto PHF carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available in sizes:

  • 30
  • 33
  • 35
  • 38
  • 40
  • 42
  • 45
  • 48
  • 50
  • 55
  • 60

Required quantity per carburettor: 1

This is item number 7 in the drawing.

(7) Pump Jet for Dellorto PHF carburetors

NV
(8) Viton-Tipped Needle Valve Assembly for Dellorto PHF carburetors

(8) Viton-Tipped Needle Valve Assembly for Dellorto PHF carburetors

Dellorto needle valve, seat and fiber washer for the PHF carburetors.

Genuine Dellorto part, Viton-tipped!

Only genuine Dellorto needles are marked with the diamond shaped "Inc" logo!

Available in size:

  • 150
  • 170
  • 200
  • 225
  • 250
  • 270
  • 300
  • 350
  • 400

Required quantity per carburettor: 1

This is item number 8 in the drawing.

(8) Viton-Tipped Needle Valve Assembly for Dellorto PHF carburetors

7450
(9) Double Float for Dellorto PHF carburetors

(9) Double Float for Dellorto PHF carburetors

This is the, double, float for the Dellorto PHF carburetors.

Originally, these came only in the early style, black, version with metal linking arm but these are being phased out in favor of the, new, white version.

Please choose the replacement for your defective float according to the part-number on your original.

Available in the following versions:

  • 7450.1 8.5 gram white - replaces 7450.1 10 gram black
  • 7450.2 12.5 gram white - replaces 7450.2 14 gram black
  • 7450.3 7.5 gram black (only 1 left in stock!)
  • 7450.3 6,5 gram white - replaces 7450.3 7.5 gram black

Required quantity per carburettor: 1

This is item number 9 in the drawing.

(9) Double Float for Dellorto PHF carburetors

6429
(10) Screw for the DOMED top cover of the Dellorto PHF carburetors

(10) Screw for the DOMED top cover of the Dellorto PHF carburetors

Screw for the, domed, top cover of the Dellorto PHF carburetors.

Required quantity per carburettor: 2

This is item number 10 in the drawing.

 

 

(10) Screw for the DOMED top cover of the Dellorto PHF carburetors

6429
(12) Screw for Dellorto PHF carburetors

(12) Screw for Dellorto PHF carburetors

Screw for the cable arm of the Dellorto PHF carburetors.

Required quantity number per carburettor: 2

This is item number 12 in the drawing.

 

 

(12) Screw for Dellorto PHF carburetors

5011
(13) Spring Washer for Dellorto PHF carburetors

(13) Spring Washer for Dellorto PHF carburetors

Spring Washer for the top cover of the Dellorto PHF carburetors.

Required quantity number per carburettor: 2

This is item number 13 in the drawing.

 

 

(13) Spring Washer for Dellorto PHF carburetors

8826
(15) Top Cover Gasket for Dellorto PHF carburetors with a domed top

(15) Top Cover Gasket for Dellorto PHF carburetors with a DOMED top

Paper gasket to seal the top cover on Dellorto PHF carburetors with a domed top.

Required quantity number per carburettor: 1

This is item number 15 in the drawing.

 

(15) Top Cover Gasket for Dellorto PHF carburetors with a domed top

PHF-ROD
(18) Internal Cable / Rod for Dellorto PHF carburetors

(18) Internal Cable / Rod for Dellorto PHF carburetors

Internal actuation cable / rod for the Dellorto PHF carburetors.

This cable / rod was originally available in 3 version of which 2 are still available:

  • Cable - 73 mm long
  • Cable - 76 mm long - This version is no longer supplied by Dellorto !
  • Non-flexible rod

You can select the required version through the drop-box.

Required quantity number per carburettor: 1

This is item number 18 in the drawing.

(18) Internal Cable / Rod for Dellorto PHF carburetors

4957
(20) Spring Washer for Dellorto PHF carburetors

(20) Spring Washer for Dellorto PHF carburetors

Spring Washer for the Dellorto PHF carburetors.

Required quantity number per carburettor: 1

This is item number 20 in the drawing.

 

 

(20) Spring Washer for Dellorto PHF carburetors

8542
(22) Screw for Dellorto PHF carburetors

(22) Screw for Dellorto PHF carburetors

Screw / Bolt that secures the top cover as well as the lower part of the top casting with domed cover on the Dellorto PHF series carburetors.

Required quantity per carburettor: 2

This is item number 22 in the drawing.

 

 

 

(22) Screw for Dellorto PHF carburetors

SlideSpring
(28) Internal Slide Spring for Dellorto PHF carburetors

(28) Internal Slide Spring for Dellorto PHF carburetors

Internal Slide Spring for the Dellorto PHF series carburetors.

Available in 3 settings:

  • Weak: Free length 125 mm, Wire diameter 1.12 mm, Spring diameter 20 mm, Number of turns 19
  • Medium: Free length 132 mm, Wire diameter 1.20 mm, Spring diameter 20 mm, Number of turns 19
  • Strong: Free length 137 mm, Wire diameter 1.25 mm, Spring diameter 20 mm, Number of turns 17

Required quantity per carburettor: 1

This is item number 28 in the drawing.

(28) Internal Slide Spring for Dellorto PHF carburetors

8525
(29) Needle Circlip for Dellorto PHF carburetors

(29) Needle Circlip for Dellorto PHF carburetors

Circlip to secure the needle on Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 29 in the drawing.

 

 

 

 

(29) Needle Circlip for Dellorto PHF carburetors

8533
(30) O-Ring for FLAT Top Cover for Dellorto PHF carburetors

(30) O-Ring for FLAT Top Cover for Dellorto PHF carburetors

Rubber (Viton) O-ring to seal the FLAT top cover on Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 30 in the drawing.

 

 

 

 

(30) O-Ring for FLAT Top Cover for Dellorto PHF carburetors

8535
(31) Pump Arm Pin for Dellorto PHF carburetors with metal top

(31) Pump Arm Pin for Dellorto PHF carburetors with metal top

Pump arm pin for the Dellorto PHF carburetors with a metal / alloy top.

Please note that there TWO versions of this pin which are NOT interchangeable!
The difference is in the material of the "lower top casting", plastic vs. metal, number 23 in the drawing.
This particular pin is for the metal top.

Required quantity number per carburettor: 1

This is item number 31 in the drawing.

(31) Pump Arm Pin for Dellorto PHF carburetors with metal top

10924
(31) Pump Arm Pin for Dellorto PHF carburetors with plastic top

(31) Pump Arm Pin for Dellorto PHF carburetors with plastic top

Pump arm pin for the Dellorto PHF carburetors with a plastic top.

Please note that there TWO versions of this pin which are NOT interchangeable!
The difference is in the material of the "lower top casting", plastic vs. metal, number 23 in the drawing.
This particular pin is for the plastic top.

Required quantity number per carburettor: 1

This is item number 31 in the drawing.

(31) Pump Arm Pin for Dellorto PHF carburetors with plastic top

7415
(32) Pump Arm Spring for Dellorto PHF carburetors

(32) Pump Arm Spring for Dellorto PHF carburetors

Pump arm spring for the Dellorto PHF carburetors.

Return spring for the pump arm.

Required quantity number per carburettor: 1

This is item number 32 in the drawing.

 

 

 

(32) Pump Arm Spring for Dellorto PHF carburetors

8426
(33) Pump Arm for Dellorto PHF carburetors

(33) Pump Arm for Dellorto PHF carburetors

Pump arm for the Dellorto PHF carburetors.

Actuator arm for the pump mechanism.

Required quantity number per carburettor: 1

This is item number 33 in the drawing.

 

 

 

(33) Pump Arm for Dellorto PHF carburetors

9330
(34) 40 Degree Cable Elbow for Dellorto PHF carburetors

(34) 40 Degree Cable Elbow for Dellorto PHF carburetors

40 degrees cable elbow for the Dellorto PHF carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 34 in the drawing.

(34) 40 Degree Cable Elbow for Dellorto PHF carburetors

10854
(34) 50 Degree Cable Elbow for Dellorto PHF carburetors

(34) 50 Degree Cable Elbow for Dellorto PHF carburetors

50 degrees cable elbow for the Dellorto PHF carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 34 in the drawing.

(34) 50 Degree Cable Elbow for Dellorto PHF carburetors

3600
(34) 70 Degree Cable Elbow for Dellorto PHF carburetors

(34) 70 Degree Cable Elbow for Dellorto PHF carburetors

70 degrees cable elbow for the Dellorto PHF carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 34 in the drawing.

(34) 70 Degree Cable Elbow for Dellorto PHF carburetors

3698
(34) 90 Degree Cable Elbow for Dellorto PHF carburetors

(34) 90 Degree Cable Elbow for Dellorto PHF carburetors

90 degrees cable elbow for the Dellorto PHF carburetors.

Please note that this elbow is NOT suitable for the BMW R90S with metal topped carburettors!

This elbow is secured into the top cover by means of Lock Nut 1691. For your convenience, you can order this lock nut along with the elbow by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 34 in the drawing.

(34) 90 Degree Cable Elbow for Dellorto PHF carburetors

1691
Lock Nut for Cable Elbow on Dellorto carburetors

Lock Nut for Cable Elbow on Dellorto carburetors

This lock nut is used on a wide variety of Dellorto carburetors to secure the cable elbow into the top cover.

Required quantity per elbow: 1

This item is usually NOT depicted in the drawing.

 

 

 

Lock Nut for Cable Elbow on Dellorto carburetors

1692
(35) Lock nut for Cable Adjuster on Dellorto PHF carburetors

(35) Lock nut for Cable Adjuster on Dellorto PHF carburetors

This is the locknut that secures the setting on the throttle cable for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 35 in the drawing.

 

(35) Lock nut for Cable Adjuster on Dellorto PHF carburetors

1481
(36) Cable Adjuster for Dellorto PHF carburetors

(36) Cable Adjuster for Dellorto PHF carburetors

Cable adjuster for the Dellorto PHF carburetors.

Fits an outer cable with an external diameter of 6.75 mm.

This cable adjuster uses Lock Nut 1692 to secure its setting.
For your convenience, you can order this lock nut right along with this adjuster by simply selecting it through the drop box above.

Required quantity per carburettor: 1

This is item number 36 in the drawing.

 

(36) Cable Adjuster for Dellorto PHF carburetors

1476A
(37) Rubber Cable Boot for Dellorto PHF carburetors

(37) Rubber Cable Boot for Dellorto PHF carburetors

Rubber cable cap for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 37 in the drawing.

 

(37) Rubber Cable Boot for Dellorto PHF carburetors

7745
(38) Screw for Choke Assembly Support on Dellorto PHF carburetors

(38) Screw for Choke Assembly Support on Dellorto PHF carburetors

Screw that secures the choke assembly to the body of the carburetor on the Dellorto PHF series carburetors.

Required quantity per carburettor: 1

This is item number 38 in the drawing.

 

 

(38) Screw for Choke Assembly Support on Dellorto PHF carburetors

8295
(39) Choke Assembly Support for Dellorto PHF carburetors

(39) Choke Assembly Support for Dellorto PHF carburetors

Choke assembly support for the Dellorto PHF series carburetors.

Required quantity per carburettor: 1

This is item number 39 in the drawing.

 

 

 

 

(39) Choke Assembly Support for Dellorto PHF carburetors

8297
(40) O Ring for Choke Assembly on Dellorto PHF carburetors

(40) O Ring for Choke Assembly on Dellorto PHF carburetors

Rubber (Viton) o-ring to seal the choke assembly on the Dellorto PHF series carburetors.

Required quantity per carburettor: 1

This is item number 40 in the drawing.

 

 

(40) O Ring for Choke Assembly on Dellorto PHF carburetors

3238
(42) Choke Piston for Dellorto PHF carburetors

(42) Choke Piston for Dellorto PHF carburetors

Choke Piston for Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 42 in the drawing.

 

 

 

 

(42) Choke Piston for Dellorto PHF carburetors

8678
(43) O-Ring for mixture screw on Dellorto PHF carburetors

(43) O-Ring for Mixture Screw on Dellorto PHF carburetors

Viton (rubber) O-Ring for mixture screw on Dellorto PHF carburetors.

Required quantity per carburetor: 1

This is item number 43 in the drawing.

 

 

(43) O-Ring for mixture screw on Dellorto PHF carburetors

8260
(44) Mixture screw spring washer for Dellorto PHF carburetors

(44) Mixture Screw Spring Washer for Dellorto PHF carburetors

Washer that keeps the mixture screw spring in place on the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 44 in the drawing.

(44) Mixture screw spring washer for Dellorto PHF carburetors

7446
(45) Mixture Screw Spring for Dellorto PHF carburetors

(45) Mixture Screw Spring for Dellorto PHF carburetors

Mixture Screw Spring for the Dellorto PHF carburetors.

Spring that secures the setting of the mixture screw of the PHF series.

Required quantity per carburettor: 1

This is item number 45 in the drawing.

 

 

(45) Mixture Screw Spring for Dellorto PHF carburetors

7449
(46) Mixture screw for Dellorto PHF carburetors

(46) Mixture Screw for Dellorto PHF carburetors

Mixture screw for the Dellorto PHF carburetors.

Total length: 33 mm

Tip length: 2.5 mm

Parallel shaft length: 17.4 mm

Please note that this version is NOT suitable for the Cagiva Mito.

Required quantity per carburettor: 1

This is item number 46 in the drawing.

(46) Mixture screw for Dellorto PHF carburetors

7673
(47) Throttle Stop Screw for Dellorto PHF carburetors

(47) Throttle Stop Screw for Dellorto PHF carburetors

Idle Stop Screw for Dellorto PHF carburetors.

Screw to set the fixed opening of the throttle slide on this series carburetors.

Total length: 29.5 mm
Please contact us by email in case that you require a different length.

Required quantity per carburettor: 1

This is item number 47 in the drawing.

 

(47) Throttle Stop Screw for Dellorto PHF carburetors

4670
(48) Throttle Stop Screw Spring for Dellorto PHF carburetors

(48) Throttle Stop Screw Spring for Dellorto PHF carburetors

Throttle stop screw spring for Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 48 in the drawing.

 

 

(48) Throttle Stop Screw Spring for Dellorto PHF carburetors

4650
(49) Throttle Stop Washer for Dellorto PHF carburetors

(49) Throttle Stop Washer for Dellorto PHF carburetors

Throttle Stop Washer for Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 49 in the drawing.

 

(49) Throttle Stop Washer for Dellorto PHF carburetors

7540
(50) Throttle Stop Screw O ring for Dellorto PHF carburetors

(50) Throttle Stop Screw O ring for Dellorto PHF carburetors

Viton O-ring to seal the throttle stop screw on the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 50 in the drawing.

 

 

(50) Throttle Stop Screw O ring for Dellorto PHF carburetors

10747
(51) Pump jet holder for Dellorto PHF carburetors

(51) Pump jet holder for Dellorto PHF carburetors

Pump jet holder for Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 51 in the drawing.

 

 

(51) Pump jet holder for Dellorto PHF carburetors

6426
(52) Fiber Ring for Dellorto PHF carburetors

(52) Fiber Ring for Dellorto PHF carburetors

Fiber ring for the pump jet holder for the Dellorto PHF carburetors.

Required quantity per carburetor: 1

This is item number 52 in the drawing.

 

(52) Fiber Ring for Dellorto PHF carburetors

6173
(53) O-ring for Dellorto PHF carburetors

(53) O-ring for Dellorto PHF carburetors

O-ring for the Dellorto PHF carburetors.

Is used on both the pump jet as well as on the choke (or starter) jet.

Required quantity per carburettor: 2

This is item number 53 in the drawing.

 

(53) O-ring for Dellorto PHF carburetors

8598
(55) O-ring for the Pump Adjustment Screw on Dellorto PHF carburetors

(55) O-ring for the Pump Adjustment Screw on Dellorto PHF carburetors

O-ring for the Adjustment Screw of the Pump of the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 55 in the drawing.

 

 

 

(55) O-ring for the Pump Adjustment Screw on Dellorto PHF carburetors

5011
(59) Spring Washer for Dellorto PHF carburetors

(59) Spring Washer for Dellorto PHF carburetors

Spring Washer for the pump jet cover of the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 59 in the drawing.

 

 

(59) Spring Washer for Dellorto PHF carburetors

7626
(61) Pump Jet Pump Diaphragm Spring for Dellorto PHF carburetors

(61) Pump Jet Pump Diaphragm Spring for Dellorto PHF carburetors

Pump Jet Pump Diaphragm Spring for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 61 in the drawing.

 

 

(61) Pump Jet Pump Diaphragm Spring for Dellorto PHF carburetors

8555
(62) Pump Diaphragm for Dellorto PHF carburetors

(62) Pump Diaphragm for Dellorto PHF carburetors

Pump Jet Pump Diaphragm Spring for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 61 in the drawing.

 

 

(62) Pump Diaphragm for Dellorto PHF carburetors

9278
(63) Pump Diaphragm Gasket for Dellorto PHF carburetors

(63) Pump Diaphragm Gasket for Dellorto PHF carburetors

Gasket that fits in between the pump diaphragm Spring and the carburetor body of the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 63 in the drawing.

 

(63) Pump Diaphragm Gasket for Dellorto PHF carburetors

8885 - 8552
(64) Main Jet Holder for Dellorto PHF carburetors

(64) Main Jet Holder for Dellorto PHF carburetors

This is the main jet holder for the Dellorto PHF carburetors.

Please note that there are TWO different versions available which are NOT interchangeable!

The available versions are:

  1. 8885 - 17 MM tall
  2. 8552 - 20 MM tall

Required quantity per carburettor: 1

This is item number 64 in the drawing.

(64) Main Jet Holder for Dellorto PHF carburetors

6109
(65) Banjo Fuel Filter for Dellorto PHF carburetors

(65) Banjo Fuel Filter for Dellorto PHF carburetors

Special fuel filter to fit the banjo fuel bolt of the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 65 in the drawing.

 

 

(65) Banjo Fuel Filter for Dellorto PHF carburetors

8557
(68) Pump Non-Return Valve for Dellorto PHF carburetors

(68) Pump Non-Return Valve for Dellorto PHF carburetors

Pump Non-Return Valve for Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 68 in the drawing.

 

 

 

 

(68) Pump Non-Return Valve for Dellorto PHF carburetors

6288
(69) Fiber Ring for the Needle Valve on the Dellorto PHF carburetors

(69) Fiber Ring for the Needle Valve on the Dellorto PHF carburetors

Fiber ring to seal the needle valve on the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 69 in the drawing.

 

 

(69) Fiber Ring for the Needle Valve on the Dellorto PHF carburetors

7346
(70) Float Pivot Pin for Dellorto PHF carburetors

(70) Float Pivot Pin for Dellorto PHF carburetors

Standard float pivot pin for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 70 in the drawing.

 

 

(70) Float Pivot Pin for Dellorto PHF carburetors

7451
(71) Float Bowl O-Ring for Dellorto PHF carburetors

(71) Float Bowl O-Ring for Dellorto PHF carburetors

Float bowl o-ring / rubber gasket for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 71 in the drawing.

 

 

(71) Float Bowl O-Ring for Dellorto PHF carburetors

4057
(73) 14 and 17 mm Float Bowl Nut Seal for Dellorto PHF carburetors

(73) 14 and 17 mm Float Bowl Nut Seal for Dellorto PHF carburetors

Float bowl nut seal for the Dellorto PHF carburetors.

Fits the 14 and 17 mm varieties of that special nut:

Required quantity per carburetor: 1

This is item number 73 in the drawing.

(73) 14 and 17 mm Float Bowl Nut Seal for Dellorto PHF carburetors

8551
(74) 14 mm Float Bowl Nut for Dellorto PHF carburetors

(74) 14 mm Float Bowl Nut for Dellorto PHF carburetors

Special Nut / Drain Plug for the float bowl on the Dellorto PHF carburetors.

Please note: there is a total of 3 different plugs available which are NOT interchangeable.

These are most easily identified by the spanner size needed for them.

This particular versions requires a 14 mm spanner.

This nut uses Fiber Seal 4057 to seal against the float bowl.

Required quantity per carburettor: 1

This is item number 74 in the drawing.

(74) 14 mm Float Bowl Nut for Dellorto PHF carburetors

9676
(74) 17 mm Float Bowl Nut for Dellorto PHF carburetors

(74) 17 mm Float Bowl Nut for Dellorto PHF carburetors

Special Nut / Drain Plug for the float bowl on the Dellorto PHF carburetors.

Please note: there is a total of 3 different plugs available which are NOT interchangeable.

These are most easily identified by the spanner size needed for them.

This particular versions requires a 17 mm spanner.

This nut uses Fiber Seal 4057 to seal against the float bowl.

Required quantity per carburettor: 1

This is item number 74 in the drawing.

(74) 17 mm Float Bowl Nut for Dellorto PHF carburetors

4570
Fiber Seal for Float Bowl Plug on Dellorto PHF carburetors

Fiber Seal for Float Bowl Plug on Dellorto PHF carburetors

Fiber seal for the float bowl nut with Drain Facility on the Dellorto PHF series carburetors.

Is used on float bowl nut 9973 with drain plug 9812.

Required quantity per carburettor when equipped with appropriate drain plug: 1

This item number is NOT in the drawing.

Fiber Seal for Float Bowl Plug on Dellorto PHF carburetors

4057
(73) 21 mm Float Bowl Nut Seal for Dellorto PHF carburetors

(73) 21 mm Float Bowl Nut Seal for Dellorto PHF carburetors

Float bowl nut seal for the Dellorto PHF carburetors.

Fits the 21 mm varieties of that special nut:

Required quantity per carburetor: 1

This is item number 73 in the drawing.

(73) 21 mm Float Bowl Nut Seal for Dellorto PHF carburetors

10238
(74) 21 mm Float Bowl Nut for Dellorto PHF carburetors

(74) 21 mm Float Bowl Nut for Dellorto PHF carburetors

Special Nut / Drain Plug for the float bowl on the Dellorto PHF carburetors.

Please note: there is a total of 3 different plugs available which are NOT interchangeable.

These are most easily identified by the spanner size needed for them.

This particular versions requires a 21 mm spanner.

This nut uses Fiber Seal 4057 to seal against the float bowl.

Required quantity per carburettor: 1

This is item number 74 in the drawing.

(74) 21 mm Float Bowl Nut for Dellorto PHF carburetors

8680
(76) 18 mm trumpet for Dellorto PHF carburetors

(76) 18 mm trumpet for Dellorto PHF carburetors

18 millimeter long trumpet for the Dellorto PHF carburetor.

Black plastic.

Required quantity per carburettor: 1

This is item number 76 in the drawing.

 

(76) 18 mm trumpet for Dellorto PHF carburetors

11248
(77) 30 mm trumpet for Dellorto PHF carburetors

(77) 30 mm trumpet for Dellorto PHF carburetors

30 millimeter long trumpet for the Dellorto PHF carburetor.

Black plastic.

Required quantity per carburettor: 1

This is item number 77 in the drawing.

 

(77) 30 mm trumpet for Dellorto PHF carburetors

C1050
C1050 Pipercross Universal Airfilter Socks for Ram Pipes

C1050 Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

These socks are easily tailored to size by shortening them with a pair of scissors.

The generous inner diameter makes them suitable for virtually all rampipes.

Created out of the famous Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

This is the "normal" version, very well suited for street and track use. Should you be using your vehicle in extremely dusty circumstances, like auto- and motocross, we recommend the Heavy Duty version, C1050MX.

Dimensions:

  • Internal diameter: 70 mm
  • External diameter: 95 mm
  • Internal height: 100 mm
  • External height: 115 mm

Before putting the socks in place, you cut them to size. Then slide them onto the ram pipes and, when desired, you can secure them in place with a simple plastic tie-strap.

Although Pipercross supplies these only in pairs, we understand the need in the market for "singles" and consequently we sell these individually.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1050 Pipercross Universal Airfilter Socks for Ram Pipes

C1050MX
C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous Heavy Duty Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

These socks are easily tailored to size by shortening them with a pair of scissors.

The generous inner diameter makes them suitable for virtually all rampipes.

Created out of not less than 3 layers of the famous, green, Heavy Duty Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

Being the heavy duty version, these socks are very well suited for use in extremely dusty circumstances like auto- and motocross.

For street and track use, the better option is to pick the normal version, C1050.

Dimensions:

  • Internal diameter: 55 mm
  • External diameter: 95 mm
  • Internal height: 95 mm
  • External height: 120 mm

Before putting the socks in place, you cut them to size. Then slide them onto the ram pipes and, when desired, you can secure them in place with a simple plastic tie-strap.

Although Pipercross supplies these only in pairs, we understand the need in the market for "singles" and consequently we sell these individually.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

C1052
C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous "enclosed" Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

Contrary to the C1050 "open" socks, this version has a rear panel with opening so that it "hugs" the ram pipe.

The generous inner diameter makes them suitable for virtually all rampipes.

The opening in the rear panel measures some 55 mm in diameter but can of course be stretched significantly thanks to the nature of the foam.

Created out of 3 layers of the the famous Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

Dimensions:

  • Internal diameter: 80 mm
  • External diameter: 110 mm
  • Internal height: 42.5 mm
  • External height: 70 mm

Simply slide the sock onto the ram pipes and, when desired, you can secure them in place with a plastic tie-strap.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

6273
(78) 8 mm Single Metal Fuel Inlet Banjo for Dellorto PHF carburetors

(78) 8 mm Single Metal Fuel Inlet Banjo for Dellorto PHF carburetors

Metal fuel inlet banjo for the Dellorto PHF carburetors for 8 mm fuel lines.

Please note that there are various versions of this inlet banjo.

This is the metal version that uses fiber washer number 4052 and banjo bolt number 4568.

For your convenience, you can order this inlet banjo complete with fiber washer or without it.

Required quantity per carburettor: 1

This is item number 78 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(78) 8 mm Single Metal Fuel Inlet Banjo for Dellorto PHF carburetors

6517
(78) 8 mm Angled Metal Fuel Inlet Banjo for Dellorto PHF carburetors

(78) 8 mm Angled Metal Fuel Inlet Banjo for Dellorto PHF carburetors

Metal fuel inlet banjo for the Dellorto PHF carburetors with the fuel union under an angle of some 45 degrees (see photo) for 8 mm fuel lines.

Please note that there are various versions of this inlet banjo.

This is the metal version that uses fiber washer number 4052 and banjo bolt number 4568.

For your convenience, you can order this inlet banjo complete with fiber washer or without it.

Required quantity per carburettor: 1

This is item number 78 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(78) 8 mm Angled Metal Fuel Inlet Banjo for Dellorto PHF carburetors

9250
(78) 8 mm Plastic Fuel Inlet Banjo for Dellorto PHF carburetors

(78) 8 mm Plastic Fuel Inlet Banjo for Dellorto PHF carburetors

Plastic fuel inlet banjo for the Dellorto PHF carburetors for 8 mm fuel lines.

This plastic version uses only a banjo bolt (number 4568) and NO fiber washer.

For your convenience, you can order this inlet banjo complete with banjo bolt or without it.

Required quantity per carburetor: 1

This is item number 78 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(78) 8 mm Plastic Fuel Inlet Banjo for Dellorto PHF carburetors

4052
(79) Banjo Bolt Fiber Washer for Dellorto PHF carburetors

(79) Banjo Bolt Fiber Washer for Dellorto PHF carburetors

Banjo bolt fiber washer for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 79 in the drawing.

 

 

(79) Banjo Bolt Fiber Washer for Dellorto PHF carburetors

4568
(80) Long Fuel Banjo Bolt for Dellorto PHF carburetors

(80) Long Fuel Banjo Bolt for Dellorto PHF carburetors

Fuel banjo bolt for the Dellorto PHF carburetors with 8 mm pipe fitting banjos only.

This bolt has an overall length of some 21 mm with a shaft length of approximately 17.5 mm and will NOT fit the banjos for 6 mm fuel lines.

Required quantity per carburettor: 1

This is item number 80 in the drawing.

 

 

(80) Long Fuel Banjo Bolt for Dellorto PHF carburetors

7890
(81) 8 mm Double Fuel Inlet Banjo for Dellorto PHF carburetors

(81) 8 mm Double Fuel Inlet Banjo for Dellorto PHF carburetors

This is the, TWIN, metal fuel inlet banjo for the Dellorto PHF carburetors for 8 mm fuel lines.

This double metal version which uses fiber washer number 4052.

This double metal version which uses banjo bolt 4568.

For your convenience, you can order this inlet banjo complete with fiber washer and banjo bolt or simply without these extras.

Required quantity per carburettor: 1

This is item number 81 in the drawing.

This banjo uses fuel line with an internal diameter of 8 mm.

(81) 8 mm Double Fuel Inlet Banjo for Dellorto PHF carburetors

9596
(83) Needle Circlip for Dellorto PHF carburetors

(83) Needle Circlip for Dellorto PHF carburetors

Circlip to secure the needle on the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 83 in the drawing.

 

 

(83) Needle Circlip for Dellorto PHF carburetors

8293
(84) Lever-Operated Choke Mechanism for Dellorto PHF carburetors - Long

(84) Lever-Operated Choke Mechanism for Dellorto PHF carburetors - Long

Lever-operated choke mechanism for the Dellorto PHF carburetors.

Please note that the working height of this version is 41 mm.

There is also a short version available which is 34 mm.

Please make sure that this is the correct version for your carburetor.

Required quantity per carburettor: 1

This is item number 84 in the drawing.

(84) Lever-Operated Choke Mechanism for Dellorto PHF carburetors - Long

10922
(85) Round Plastic Top Cover for Dellorto PHF carburetors

(85) Round Plastic Top Cover for Dellorto PHF carburetors

Round, flat, plastic top cover for the Dellorto PHF carburetors.

Required quantity per carburettor: 1

This is item number 85 in the drawing.

 

 

 

 

(85) Round Plastic Top Cover for Dellorto PHF carburetors

1104
(86) Throttle Cable Adjuster for Dellorto PHF carburetors

(86) Throttle Cable Adjuster for Dellorto PHF carburetors

Throttle cable adjuster for the Dellorto PHF series carburetors.

Required number per carburettor: 1

This is item number 86 in the drawing.

 

 

 

 

(86) Throttle Cable Adjuster for Dellorto PHF carburetors

52514
(89) Service Kit for Dellorto PHF carburetors

(89) Service Kit for Dellorto PHF carburetors

Dellorto factory-original service kit for the Dellorto PHF carburetors.

Contains all required fiber rings, gaskets and cable boot.

Required quantity per carburettor: 1

This is item number 83 in the drawing.

 

 

(89) Service Kit for Dellorto PHF carburetors

52557
(89) Service Kit for Dellorto PHF M carburetors - Cagiva

(89) Service Kit for Dellorto PHF M carburetors - Cagiva

Service kit for the Dellorto PHF M-series carburetors as used by Cagiva.

Contains all required fiber rings, gaskets etc to freshen up 1 carburetor.

Required quantity per carburettor: 1

This is item number 83 in the drawing.

 

 

(89) Service Kit for Dellorto PHF M carburetors - Cagiva

15760
(102) Single white plastic float for Dellorto PHF carburetors

(102) Single white plastic float for Dellorto PHF carburetors

Single, white plastic, float for the Dellorto PHF carburetors.

Available in the following versions:

  • 15760.3 - 4.0 grams
  • 15760.4 - 5.2 grams
  • 15760.5 - 3.6 grams

Required quantity per carburettor: 2

This is item number 102 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHF.

(102) Single white plastic float for Dellorto PHF carburetors

9794
(102) Single black plastic float for Dellorto PHF carburetors

(102) Single black plastic float for Dellorto PHF carburetors

Single, black plastic, float for the Dellorto PHF carburetors.

Available in the following versions:

  • 9794.1 - 3.5 gram
  • 9794.3 - 3.5 gram
  • 9794.4 - 4.5 gram
  • 9794.5 - 2.8 gram

Required quantity per carburettor: 2

This is item number 102 in the drawing.

Click HERE for instructions on how to set the float level of the Dellorto PHF.

(102) Single black plastic float for Dellorto PHF carburetors

9008
Breather Pipe Connection for Dellorto PHF carburetors

Breather Pipe Connection for Dellorto PHF carburetors

This breather pipe connector will fit a wide range of Dellorto carburetors, amongst which the PHF series carburettors.

This pipe has 5 mm push fit in the carburettor body and connects to a 3.8 mm internal diameter breather line.

Required quantity per carburettor: 1

This item is NOT shown in the drawing.

Breather Pipe Connection for Dellorto PHF carburetors

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15 MM
  • 0.25 MM
  • 0.4 MM
  • 0.8 MM
  • 1.6 MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

gatestextiel8mm
Gates textile covered fuel line hose with 8 mm inner diameter

Gates textile covered fuel line hose with 8 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

Gates textile covered fuel line hose with 8 mm inner diameter

GREENFUEL8MM-50cm
Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

Alternatively, this hose simply looks great when used with the "Endless band & Buckle" hose clamps like in the photo.

Please note:
This hose is NOT E10 resistant.
Do not use this hose if you are not able to avoid using Ethanol-containing fuels.

Italian style clear green fuel line hose with 8 mm inner diameter

jubilee11-13
11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

PRO805
Sytec Pro-Line in-line fuel filter - 8 mm

Sytec Pro-Line in-line fuel filter - 8 mm

In line fuel filter with cleanable / replaceable filter.

Suitable for 8 mm internal diameter fuel hoses.

Replacement filter elements are available HERE.

Chrome finish.

Toughened glass phial.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

Supplied with 2 Jubilee clips.

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Sytec Pro-Line in-line fuel filter - 8 mm

PRO896
Replacement elements for Sytec in-line fuel filter

Replacement elements for Sytec in-line fuel filter

3 replacement elements for the Sytec Pro-Line in-line fuel filter.

Come complete with new rubber seals.

These elements fit our PRO804 and PRO805 Sytec in-line fuel filters.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

 

 

 

 

Replacement elements for Sytec in-line fuel filter

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm - SOLD OUT AT THE MOMENT!

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

Available from our Stock

MANOMETER2
2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easily read scale
  • Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

2 Column Manometer - Synchrometer Carbtune Pro

MANOMETER4
4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easy to read scale
  • Comes complete with 4 x 5 mm and 4 x 6 mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

4 Column Manometer - Synchrometer Carbtune Pro

9679
Brass vacuum take-off adapter for carburetors and manifolds

Brass vacuum take-off adapter for carburetors and manifolds

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Also fits the Weber DCOE series carburettors and Solex ADDHE.

 

Brass vacuum take-off adapter for carburetors and manifolds

DD0906
Dellorto Carburatori Sticker - Large

Dellorto Carburatori Sticker - Large

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 9 x 3 cm (3.54 x 1.2 inches).

This is Number 1 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Large

DD0909
Dellorto Carburatori Sticker - Medium

Dellorto Carburatori Sticker - Medium

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 8 x 4 cm (3.1 x 1.55 inches).

This is Number 2 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Medium

DD0905
Dellorto Carburatori Sticker - Small - Low

Dellorto Carburatori Sticker - Small - Low

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 6 x 2 cm (2.4 x 0.8 inches).

This is Number 3 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Small - Low

Patch
Dellorto Carburatori Sew-On Patch

Dellorto Carburatori Sew-On Patch

Official issue sew-on patch with the Dellorto logo and Italian flag "tricolore" colors.

Measures 12 x 6.5 cm (4.7 x 2.6 inches).

Elaborately embroidered.

 

 

Dellorto Carburatori Sew-On Patch