12 Volt Fuel Pumps
12 Volt Fuel Pumps

12 Volt Fuel Pumps

12 Volt Fuel Pumps.

On this page you will find fuel pumps specifically for vehicles with a 12 Volt electrical system.

12 Volt Fuel Pumps

!
SSRK
Facet CUBE Solid State ROAD Fuel Pump Kit

Facet CUBE Solid State ROAD Fuel Pump Kit

Facet Solid State ROAD Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State ROAD fuel pump is suitable for engines of up to circa 130 HP.

Pump specification:

  • Flow rate 12 Gallons/hour - 45 liters/hour
  • Pressure: 2.5 - 3.0 PSI - 0.17 - 0.20 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State ROAD Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State ROAD Fuel Pump Kit

SSR
Facet CUBE Solid State ROAD Fuel Pump - Pump Only

Facet CUBE Solid State ROAD Fuel Pump - Pump Only

Facet CUBE Solid State ROAD Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State ROAD fuel pump is suitable for engines of up to circa 130 HP.

Pump specification:

  • Flow rate 12 Gallons/hour - 45 liters/hour
  • Pressure: 2.5 - 3.0 PSI - 0.17 - 0.20 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State ROAD Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State ROAD Fuel Pump - Pump Only

SSFRK
Facet CUBE Solid State FAST ROAD Fuel Pump Kit

Facet CUBE Solid State FAST ROAD Fuel Pump Kit

Facet Solid State FAST ROAD Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State FAST ROAD fuel pump is suitable for engines of up to circa 150 HP.

Pump specification:

  • Flow rate 32 Gallons/hour - 120 liters / hour
  • Pressure: 4 - 7 PSI - 0.27 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State FAST ROAD Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State FAST ROAD Fuel Pump Kit

SSFR
Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

Facet CUBE Solid State FAST ROAD Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State FAST ROAD fuel pump is suitable for engines of up to circa 150 HP.

Pump specification:

  • Flow rate 32 Gallons/hour - 120 liters / hour
  • Pressure: 4 - 7 PSI - 0.27 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State FAST ROAD Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

SSCK
Facet CUBE Solid State COMPETITION Fuel Pump Kit

Facet CUBE Solid State COMPETITION Fuel Pump Kit

Facet Solid State COMPETITION Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State COMPETITION fuel pump is suitable for engines of up to circa 180 HP.

Pump specification:

  • Flow rate 25 Gallons/hour - 95 liters/hour
  • Pressure: 6.0 - 7.0 PSI - 0.41 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State COMPETITION Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State COMPETITION Fuel Pump Kit

SSC
Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

Facet CUBE Solid State COMPETITION Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State COMPETITION fuel pump is suitable for engines of up to circa 180 HP.

Pump specification:

  • Flow rate 25 Gallons/hour - 95 liters/hour
  • Pressure: 6.0 - 7.0 PSI - 0.41 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State COMPETITION Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

RTWK
Facet GOLD-FLO Red top Competition Fuel Pump Kit

Facet GOLD-FLO Red top Competition Fuel Pump Kit

Facet GOLD-FLO Red top competition fuel pump kit suitable for engines of 200+ BHP.

Pump specification:

  • Flow rate 45 Gallons/hour / 170 liters/hour
  • Pressure: 6.5 - 8 PSI / 0.45 - 0.55 Bar
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • Mounting isolation feet
  • 10 mm Inlet and outlet unions
  • Spare internal filter
  • Terminated earthing wire
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread
Fuel Unions for fuel lines with 10 mm internal diameter

Due to its operating pressure of up to 8 PSI (some 0.55 Bar), the GOLD-FLO Red Top Competition pump usually requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet GOLD-FLO Red top Competition Fuel Pump Kit

RTW
Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

Facet Red Top competition fuel pump, suitable for engines of 200+ BHP.

Pump specification:

  • Flow rate 45 Gallons/hour / 170 liters/hour
  • Pressure: 6.5 - 8 PSI / 0.45 - 0.55 Bar
  • Dry prime height 12 inches / 0.6 Mtrs
  • Pipe union thread size: 1/4 NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

Couplings Specifications:
Connection to pump body: 1/4" NPTF tapered thread

Due to its operating pressure of up to 8 PSI (some 0.55 Bar), the GOLD-FLO Red Top Competition pump usually requires a pressure regulator to prevent your carburetor(s) from flooding but please check your system requirements to make sure.
A variety of pressure regulators can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet GOLD-FLO Red Top Competition Fuel Pump - Pump only

WFP502
Airtex 12 Volt Low-Pressure Fuel Pump

Airtex 12 Volt Low-Pressure Fuel Pump

This is a special, low-pressure fuel pump for vehicles with a 12 Volt electrical system.

Thanks to its low pressure of 4.5 PSI / 0.31 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

Pump specification:

  • Flow rate: 90 - 130 liters/hour
  • Pressure: 2.5 - 4.5 PSI / 0.17 - 0.31 Bar
  • Pipe union thread size: 1/8" NPTF tapered thread
  • Power supply: 12 Volt Negative Earth
  • Pump Length: 172 mm
  • Pump Diameter: 54 mm
  • Draws a current of some 5 Amps
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

The kit includes:

  • Pump
  • In-line fuel filter
  • Mounting bracket and materials
  • 8 mm inlet and outlet unions with fuel hose and hose clips
  • Installation instructions

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Always operate this pump with the proper filter installed as failure to do so will void the warranty!
Replacement filters can be found HERE.

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Airtex 12 Volt Low-Pressure Fuel Pump

SYTECPL031
Sytec Replacement Fuel Pump for Weber PL031 - Aston Martin Virage

Sytec Replacement Fuel Pump for Weber PL031 - Aston Martin Virage

Sytec replacement pump for the long obsolete Weber PL-031 fuel pump as used on, amongst others, the 1990 - 1996 Aston Martin Virage and Virage Volante.

The Weber PL031 is no longer produced yet it is a vital part of the car's fuel system.

Systec stepped in and produces this replacement pump in the USA.

Please note: this pump requires a high quality pre-filter to avoid contamination.

Specifications:

  • Fittings In:- Jic 6
  • Fittings Out:- Jic 6
  • Voltage:-12v
  • Flow Ltr/Hr (Max):- 348
  • Flow Ltr/Hr @ 3 Bar (44psi):- 270
  • Flow Ltr/Hr @ 5 Bar (73psi):- 222
  • Location To Tank (Mtrs) 0.6
  • Thread Size:-10x1mm SFT
  • Length (mm):- 160
  • Diameter (mm):- 43
  • Weight (Kg):- 0.46

Limited availability!

Sytec Replacement Fuel Pump for Weber PL031 - Aston Martin Virage

SYTECPL031
Sytec Replacement Fuel Pump for Weber PL031 - Ferrari F40

Sytec Replacement Fuel Pump for Weber PL031 - Ferrari F40

Here we have a Sytec replacement for the long obsolete Weber PL-031 fuel pump as used on, amongst others, the Ferrari F40.

The Weber PL031 is no longer produced yet it is a vital part of the car's fuel system.

Sytec stepped in and produces this replacement pump in the USA.

Please note: this pump requires a high quality pre-filter to avoid contamination.

Specifications:

  • Fittings In:- Jic 6
  • Fittings Out:- Jic 6
  • Voltage:-12v
  • Flow Ltr/Hr (Max):- 348
  • Flow Ltr/Hr @ 3 Bar (44psi):- 270
  • Flow Ltr/Hr @ 5 Bar (73psi):- 222
  • Location To Tank (Mtrs) 0.6
  • Thread Size:-10x1mm SFT
  • Length (mm):- 160
  • Diameter (mm):- 43
  • Weight (Kg):- 0.46

Limited availability!

Sytec Replacement Fuel Pump for Weber PL031 - Ferrari F40

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch